주요 콘텐츠로 건너뛰기

Fix Your Stuff

Right to Repair

Parts & Tools

소개

The motherboard connects all parts of the camera together. This guide will show you how to disassemble the Canon Powershot S200 in order to reach the motherboard.

부품

지정된 부품이 없습니다.

  1. Slide the grey latch to open the battery compartment. Slide the grey latch to open the battery compartment.
    • Slide the grey latch to open the battery compartment.

  2. Push and slide the orange retaining clip to the right to remove the battery. Push and slide the orange retaining clip to the right to remove the battery.
    • Push and slide the orange retaining clip to the right to remove the battery.

  3. Remove battery from the camera.
    • Remove battery from the camera.

  4. Remove the lanyard.
    • Remove the lanyard.

  5. Be careful to keep track of the different screw sizes as you proceed with this guide.
    • Be careful to keep track of the different screw sizes as you proceed with this guide.

    • Find the bottom face of the camera. Remove the two 2.3mm screws beneath the name plate and the two 2.8 mm screws surrounding the threaded tripod mount.

  6. Remove the 3.8mm screw from the back face of the camera.
    • Remove the 3.8mm screw from the back face of the camera.

  7. Remove the two 2.3mm screws from the right face of the camera.
    • Remove the two 2.3mm screws from the right face of the camera.

  8. Remove the two outer 3.2mm screws from the left side of the camera
    • Remove the two outer 3.2mm screws from the left side of the camera

    • Remove the two inner 3.7mm screws from the left side of the camera.

  9. Pull the back face panel away from the front end of the body. This may take some wiggling and force.
    • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

  10. Remove the CF card door from the left side of the camera body. Remove the CF card door from the left side of the camera body.
    • Remove the CF card door from the left side of the camera body.

  11. Slide the rubber digital a/v cap out of place on the front plate. Slide the rubber digital a/v cap out of place on the front plate.
    • Slide the rubber digital a/v cap out of place on the front plate.

  12. Remove the front face by sliding it off.
    • Remove the front face by sliding it off.

  13. Remove the rubber seal that covers the right side of the viewfinder.
    • Remove the rubber seal that covers the right side of the viewfinder.

  14. Remove the two 3.9mm screws that hold the laminated cooper sheet.
    • Remove the two 3.9mm screws that hold the laminated cooper sheet.

  15. Remove the wire connections that connect along the bottom of the motherboard. Remove the wire connections that connect along the bottom of the motherboard.
    • Remove the wire connections that connect along the bottom of the motherboard.

  16. Remove the single 3.8mm screw that is on the motherboard.
    • Remove the single 3.8mm screw that is on the motherboard.

  17. Remove the motherboard from the main frame of the camera body.
    • Remove the motherboard from the main frame of the camera body.

결론

To reassemble your device, follow these instructions in reverse order.

Orlando Zuniga

회원 가입일: 2011년 04월 14일

11 평판

안내서 1개 작성함

Cal Poly, Team 20-70, Walters Spring 2011 Cal Poly, Team 20-70, Walters Spring 2011 회원

CPSU-WALTERS-S11S20G70

5 회원들

안내서 4개 작성하였습니다

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 8

전체 시간: 1,656