주요 콘텐츠로 건너뛰기

Canon Powershot SX30 IS Back Camera Housing Replacement

필요한 것

  1. Canon Powershot SX30 IS Back Camera Housing Replacement, Back Camera Housing: 1 단계, 이미지 1/2 Canon Powershot SX30 IS Back Camera Housing Replacement, Back Camera Housing: 1 단계, 이미지 2/2
    • Position the camera so that the right side is visible as shown.

    • Unscrew the two 6 mm screws shown using a screwdriver.

  2. Canon Powershot SX30 IS Back Camera Housing Replacement: 2 단계, 이미지 1/3 Canon Powershot SX30 IS Back Camera Housing Replacement: 2 단계, 이미지 2/3 Canon Powershot SX30 IS Back Camera Housing Replacement: 2 단계, 이미지 3/3
    • Remove the plastic flap by pressing down on the center of the hinge and pulling on the flap with the spudger.

    • Then, unscrew the lone 6mm screw that was under the plastic flap.

  3. Canon Powershot SX30 IS Back Camera Housing Replacement: 3 단계, 이미지 1/2 Canon Powershot SX30 IS Back Camera Housing Replacement: 3 단계, 이미지 2/2
    • Turn the camera so that the bottom is visible, as shown.

    • Unscrew the three 4mm screws shown red using a screwdriver.

    • Unscrew the single 6mm screw.

    • Do not touch the screw shown yellow, removal is unnecessary. (Note: the top right yellow screw should be removed)

  4. Canon Powershot SX30 IS Back Camera Housing Replacement: 4 단계, 이미지 1/1
    • Turn the camera so the back side is visible, as shown.

    • Unscrew the two 6mm screws.

  5. Canon Powershot SX30 IS Back Camera Housing Replacement: 5 단계, 이미지 1/1
    • Gently remove the back cover using the spudger.

    • Exercise caution, as the wire inside is fragile.

  6. Canon Powershot SX30 IS Back Camera Housing Replacement: 6 단계, 이미지 1/2 Canon Powershot SX30 IS Back Camera Housing Replacement: 6 단계, 이미지 2/2
    • Detach the wire by lifting the small black bar that holds it to the main body of the camera.

  7. Canon Powershot SX30 IS Back Camera Housing Replacement: 7 단계, 이미지 1/1
    • Attach the new cover onto the camera.

  8. Canon Powershot SX30 IS Back Camera Housing Replacement: 8 단계, 이미지 1/1
    • Reattach the wire to your new rear casing.

  9. Canon Powershot SX30 IS Back Camera Housing Replacement: 9 단계, 이미지 1/1
    • Close the back cover, and re-insert appropriate screws.

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Ellis DeVoe

회원 가입일: 04/14/15

580 평판

안내서 5개 작성하였습니다

Cal Poly, Team 5-12, Maness Spring 2015 Cal Poly, Team 5-12, Maness Spring 2015 회원

CPSU-MANESS-S15S5G12

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 12

전체 시간: 1,314