주요 콘텐츠로 건너뛰기

Cirago M9030 IDE Connector Replacement

필요한 것

  1. Cirago M9030 IDE Connector Replacement, Cover: 1 단계, 이미지 1/1
    • Use a Phillips #00 screwdriver to unscrew the four 1.1mm long screws on each corner located at the top of the cover.

  2. Cirago M9030 IDE Connector Replacement: 2 단계, 이미지 1/1
    • Similar to the last step, flip the cover over and use a Phillips #00 screwdriver to unscrew the four 1.1mm long screws on each corner located at the bottom of the cover.

    • Remove the warranty sticker across the bottom.

  3. Cirago M9030 IDE Connector Replacement: 3 단계, 이미지 1/2 Cirago M9030 IDE Connector Replacement: 3 단계, 이미지 2/2
    • Gently take the cover apart using your hands separating the top and bottom.

    • The outer shell is expected to easily come apart.

  4. Cirago M9030 IDE Connector Replacement, Hard Drive: 4 단계, 이미지 1/1
    • Make sure that the screen of the device is facing down.

  5. Cirago M9030 IDE Connector Replacement: 5 단계, 이미지 1/3 Cirago M9030 IDE Connector Replacement: 5 단계, 이미지 2/3 Cirago M9030 IDE Connector Replacement: 5 단계, 이미지 3/3
    • Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive.

    • Raise the bottom edge of the hard drive 15 degrees up from the device.

  6. Cirago M9030 IDE Connector Replacement: 6 단계, 이미지 1/3 Cirago M9030 IDE Connector Replacement: 6 단계, 이미지 2/3 Cirago M9030 IDE Connector Replacement: 6 단계, 이미지 3/3
    • Place fingers on the IDE connectors gently picking up and sliding the hard drive out from the IDE module.

  7. Cirago M9030 IDE Connector Replacement, IDE Connector: 7 단계, 이미지 1/2 Cirago M9030 IDE Connector Replacement, IDE Connector: 7 단계, 이미지 2/2
    • Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard located at the top.

  8. Cirago M9030 IDE Connector Replacement: 8 단계, 이미지 1/1
    • Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

  9. Cirago M9030 IDE Connector Replacement: 9 단계, 이미지 1/2 Cirago M9030 IDE Connector Replacement: 9 단계, 이미지 2/2
    • Using the plastic opening tool, completely lift the metal bracket off of the motherboard.

    • Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

  10. Cirago M9030 IDE Connector Replacement: 10 단계, 이미지 1/1
    • Using the plastic opening tool, completely lift the ribbon off of the motherboard.

  11. Cirago M9030 IDE Connector Replacement: 11 단계, 이미지 1/2 Cirago M9030 IDE Connector Replacement: 11 단계, 이미지 2/2
    • Completely remove the IDE connector from the device.

    • The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Ryan Sutardji

회원 가입일: 06/29/12

171 평판

안내서 7개 작성하였습니다

Cal Poly, Team 1-4, Regan SU 2012 Cal Poly, Team 1-4, Regan SU 2012 회원

CPSU-REGAN-SU12S1G4

4 회원들

안내서 7개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 963