기기를 수리하세요 커뮤니티 상점

Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement

소개

Follow this guide to replace the eccentric arms on a 2018 Classen Sod Cutter model HSC18AHD.

필요한 것

  1. 주의: 1-4 단계들은 진행 중으로 표시된 안내서에서 제공되었습니다.

    Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Safety precautions: 1 단계, 이미지 1/2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Safety precautions: 1 단계, 이미지 2/2

    • Make sure the engine is off and cool to the touch before you proceed.

    편집

  2. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 2 단계, 이미지 1/1

    • Place wheel chocks against the roller and rear wheel to prevent the machine from moving.

    편집

  3. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 3 단계, 이미지 1/2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 3 단계, 이미지 2/2

    • Flip the gas shutoff switch next to the motor to the left into the off position.

    편집

  4. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 4 단계, 이미지 1/2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 4 단계, 이미지 2/2

    • Grab the plastic housing at the end of the spark plug wire.

    • Pull firmly to disconnect the wire from the spark plug.

    편집

  6. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Remove the eccentric arms: 5 단계, 이미지 1/1

    • Use a 3/4 inch socket to remove the two bolts on the eccentric arm.

    • You may need to use a 3/4 inch wrench in combination with the socket wrench to hold the nuts in place.

    • During reassembly, apply threadlocker to the bolt securing the eccentric arm to the blade arm.

    편집

  7. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 6 단계, 이미지 1/2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 6 단계, 이미지 2/2

    • Remove the plastic washer from between the eccentric arm and the blade arm.

    편집

  8. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 7 단계, 이미지 1/1

    • Lift the eccentric arm away from the blade arm.

    편집

  9. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 8 단계, 이미지 1/2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 8 단계, 이미지 2/2

    • Remove the steel washer from the eccentric shaft.

    편집

  10. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 9 단계, 이미지 1/1

    • Remove the plastic washer from the eccentric shaft.

    편집

  11. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 10 단계, 이미지 1/2 Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: 10 단계, 이미지 2/2

    • Remove the eccentric arm and plastic washer from the eccentric shaft.

    • Repeat steps 5–10 for the other eccentric arm.

    • During reassembly, use a grease gun to add grease to the bearings through the two Zerk fittings on each eccentric arm.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 1명과 함께

Sam Omiotek

회원 가입일: 02/25/19

72,866 평판

안내서 288개 작성하였습니다

배지: 35

배지 +32개 더

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 8

30일 전: 36

전체 시간: 1,444