주요 콘텐츠로 건너뛰기

소개

This outer cover is the main cover that protects the inner electrical components. Perform the guide on a flat non-conductive surface to avoid electrical shock and damage to your device.

부품

지정된 부품이 없습니다.

  1. Turn the power switch, the leftmost knob, counterclockwise to off. Turn the power switch, the leftmost knob, counterclockwise to off.
    • Turn the power switch, the leftmost knob, counterclockwise to off.

  2. Turn the device around and firmly pull the power cable plug to remove it from the radio. Turn the device around and firmly pull the power cable plug to remove it from the radio.
    • Turn the device around and firmly pull the power cable plug to remove it from the radio.

  3. Unscrew the securing cap counterclockwise from the antenna connector. Unscrew the securing cap counterclockwise from the antenna connector.
    • Unscrew the securing cap counterclockwise from the antenna connector.

  4. Gently pull the antenna cable to remove it from the back of the radio. Gently pull the antenna cable to remove it from the back of the radio.
    • Gently pull the antenna cable to remove it from the back of the radio.

  5. Unscrew the cap counterclockwise on the microphone plug to disconnect the cable. Unscrew the cap counterclockwise on the microphone plug to disconnect the cable.
    • Unscrew the cap counterclockwise on the microphone plug to disconnect the cable.

  6. Gently unplug the microphone plug.
    • Gently unplug the microphone plug.

  7. Unscrew the top four 6.0mm Phillips head screws counterclockwise on the left and right side of the device using a #1 Phillips head screwdriver. Unscrew the top four 6.0mm Phillips head screws counterclockwise on the left and right side of the device using a #1 Phillips head screwdriver.
    • Unscrew the top four 6.0mm Phillips head screws counterclockwise on the left and right side of the device using a #1 Phillips head screwdriver.

  8. Gently life and remove the top cover. Gently life and remove the top cover. Gently life and remove the top cover.
    • Gently life and remove the top cover.

  9. Gently set down on a hard, flat, non-conductive surface to minimize risk of shock or breaking your radio. Carefully flip the radio over. Carefully flip the radio over.
    • Gently set down on a hard, flat, non-conductive surface to minimize risk of shock or breaking your radio.

    • Carefully flip the radio over.

  10. Unscrew the four 6.0mm Phillips head screws counterclockwise on the left and right side of the device that connect the remaining cover, using a #1 Phillips head screwdriver. Unscrew the four 6.0mm Phillips head screws counterclockwise on the left and right side of the device that connect the remaining cover, using a #1 Phillips head screwdriver.
    • Unscrew the four 6.0mm Phillips head screws counterclockwise on the left and right side of the device that connect the remaining cover, using a #1 Phillips head screwdriver.

  11. Watch out for the wires connected to the speaker. These short wires will not allow you to move the cover very far. Gently lift and remove the case cover. Gently lift and remove the case cover.
    • Watch out for the wires connected to the speaker. These short wires will not allow you to move the cover very far.

    • Gently lift and remove the case cover.

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Chase

회원 가입일: 2013년 10월 20일

261 평판

안내서 2개 작성하였습니다

Cal Poly, Team 11-37, Amido Fall 2013 Cal Poly, Team 11-37, Amido Fall 2013 회원

CPSU-AMIDO-F13S11G37

4 회원들

안내서 9개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 1

지난 30일: 7

전체 시간: 1,235