기기를 수리하세요 커뮤니티 상점

Cracking the Case

단지 전제 조건
이 안내서는 다른 가이드의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

소개

This guide is not for any specific repair, rather it is for cracking the device open in order to diagnose and treat your its inefficiencies.

필요한 것

  1. Cracking the Case, Cracking the Case: 1 단계, 이미지 1/1

    • Turn the device upside down so that the three rubber pads are facing up.

    번역하기

  2. Cracking the Case: 2 단계, 이미지 1/1

    • Use a heat gun (set to low) to apply heat to one of the rubber pads until you can easily remove the pad. This step takes around 5-7 minutes.

    번역하기

  3. Cracking the Case: 3 단계, 이미지 1/1

    • Remove the heated rubber pad with a plastic opening tool.

    • Repeat steps 2 and 3 for the two remaining rubber pads.

    번역하기

  5. Cracking the Case: 4 단계, 이미지 1/2 Cracking the Case: 4 단계, 이미지 2/2

    • Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver.

    번역하기

  6. Cracking the Case: 5 단계, 이미지 1/3 Cracking the Case: 5 단계, 이미지 2/3 Cracking the Case: 5 단계, 이미지 3/3

    • Open the device along its seam.

    • Be careful when separating the device because there are wires connecting the two seperate halves.

    번역하기

  7. Cracking the Case: 6 단계, 이미지 1/1

    • Disconnect the ribbon cable connector from the top half of the device by pulling outward and parallel to the connecting pins.

    번역하기

  8. Cracking the Case: 7 단계, 이미지 1/2 Cracking the Case: 7 단계, 이미지 2/2

    • Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 5명과 함께

Jared Everingham

회원 가입일: 01/23/14

368 평판

안내서 3개 작성하였습니다

배지: 11

배지 +8개 더

팀

Cal Poly, Team 9-28, Maness Winter 2014 Cal Poly, Team 9-28, Maness Winter 2014 회원

CPSU-MANESS-W14S9G28

4 회원들

안내서 7개 작성하였습니다

댓글 한 개

My product is On Stage I. It's too old. The screw fixing posts protruding from the plastic casing have broken on their own. As a result, the upper and lower shells cannot be completely sealed. When music is played, sound waves leak out of the gaps. It sounds thin and has no depth. It's like placing four speaker units directly outside the enclosure. Bass cannot resonate inside the enclosure, but travels through the bass hole in the middle. I really like this speaker. There's no way I'm giving it up. Is there any way to solve this? Should I look for a used case or use an existing case to rebuild the screw mounting posts? What should I do if I choose to rebuild?

怪醫杜立德 - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 117