주요 콘텐츠로 건너뛰기

DJI Phantom 4 Advanced Shell Replacement

단지 전제 조건
이 안내서는 다른 가이드의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

필요한 것

  1. DJI Phantom 4 Advanced Shell Replacement, Propeller: 1 단계, 이미지 1/2 DJI Phantom 4 Advanced Shell Replacement, Propeller: 1 단계, 이미지 2/2
    • Use your finger tips to pinch the damaged propeller.

    • Twist the propeller counterclockwise and pull up to remove.

  2. DJI Phantom 4 Advanced Shell Replacement, Shell: 2 단계, 이미지 1/2 DJI Phantom 4 Advanced Shell Replacement, Shell: 2 단계, 이미지 2/2
    • Remove the eight 7 mm hex screws by turning counterclockwise with a 2 mm hex bit.

  3. DJI Phantom 4 Advanced Shell Replacement: 3 단계, 이미지 1/1
    • Pry the LED motor covers off with a metal spudger.

    • The prying location is marked by an indent that points outward from the arm.

  4. DJI Phantom 4 Advanced Shell Replacement: 4 단계, 이미지 1/1
    • Pry the paper covering off the four corners with a metal spudger.

  5. DJI Phantom 4 Advanced Shell Replacement: 5 단계, 이미지 1/1
    • Remove the twelve 8.7 mm hex screws with a 2 mm hex bit from the motor bases.

  6. DJI Phantom 4 Advanced Shell Replacement: 6 단계, 이미지 1/2 DJI Phantom 4 Advanced Shell Replacement: 6 단계, 이미지 2/2
    • Flip the drone on its back

    • Remove the eight 4.5 mm hex screws by turning them counterclockwise with a 1.5 mm hex bit.

    • Separate the mesh from the drone by pulling up gently and rocking left to right.

    • The cable connects from the camera to the drone. Pulling up could rip the connection. Tilt the mesh 90 degrees towards the cable.

  7. DJI Phantom 4 Advanced Shell Replacement: 7 단계, 이미지 1/1
    • Remove two 1.2mm screws using the JIS #000 bit from the camera cable retaining bracket.

  8. DJI Phantom 4 Advanced Shell Replacement: 8 단계, 이미지 1/1
    • Lift the camera connector at one end with your hand and remove the mesh.

  9. DJI Phantom 4 Advanced Shell Replacement: 9 단계, 이미지 1/3 DJI Phantom 4 Advanced Shell Replacement: 9 단계, 이미지 2/3 DJI Phantom 4 Advanced Shell Replacement: 9 단계, 이미지 3/3
    • Remove the two 1.2 mm screws using a JIS #000 bit from the antenna retaining bracket.

    • Pull the four U.FL antennae up.

    • The U.FL antenna connectors are fragile.

    • Remove the two 4 mm screws using a JIS #000 bit.

  10. DJI Phantom 4 Advanced Shell Replacement: 10 단계, 이미지 1/2 DJI Phantom 4 Advanced Shell Replacement: 10 단계, 이미지 2/2
    • Pry apart the clamshell at the motor end.

    • Separate the clamshell.

    • Two wires connect from the lower frame to the upper frame at the front of the drone. Pulling the clamshell apart hard may damage the connectors and wires.

  11. DJI Phantom 4 Advanced Shell Replacement: 11 단계, 이미지 1/1
    • Press the connector tabs with a spudger and pull on the wire simultaneously.

    • Remove the shell from the rest of the drone.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

David Hudson

회원 가입일: 10/08/18

301 평판

안내서 2개 작성하였습니다

Cal Poly, Team S15-G6, White Fall 2018 Cal Poly, Team S15-G6, White Fall 2018 회원

CPSU-WHITE-F18S15G6

4 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 51