기기를 수리하세요 커뮤니티 상점

DeWALT Hammer Drill DW511 Power Cord Replacement

소개

Welcome to the Dewalt Hammer Drill DW511 power cord replacement guide. The power cord is an important part of the drill that delivers power to the device. You would want to replace the power cord because of a frayed or damaged cord. A common issue with a damaged power cord is the drill not running.

Caution should be taken when working with the power cord. It needs to be unplugged before working on any part of the drill.

필요한 것

  1. DeWALT Hammer Drill DW511 Power Cord Replacement, Back Cover: 1 단계, 이미지 1/3 DeWALT Hammer Drill DW511 Power Cord Replacement, Back Cover: 1 단계, 이미지 2/3 DeWALT Hammer Drill DW511 Power Cord Replacement, Back Cover: 1 단계, 이미지 3/3

    • Remove three 19 mm T20 Torx screws from the back of the drill.

    번역하기

  2. DeWALT Hammer Drill DW511 Power Cord Replacement: 2 단계, 이미지 1/3 DeWALT Hammer Drill DW511 Power Cord Replacement: 2 단계, 이미지 2/3 DeWALT Hammer Drill DW511 Power Cord Replacement: 2 단계, 이미지 3/3

    • Place an opening tool in the groove line of the handle and pop the back loose.

    • Grab the drill with two hands and pull the cover off.

    번역하기

  4. DeWALT Hammer Drill DW511 Power Cord Replacement, Power Cord: 3 단계, 이미지 1/2 DeWALT Hammer Drill DW511 Power Cord Replacement, Power Cord: 3 단계, 이미지 2/2

    • Firmly grab the body of the trigger.

    • Slowly pull the trigger until the entire body is out and only attached by wires.

    번역하기

  5. DeWALT Hammer Drill DW511 Power Cord Replacement: 4 단계, 이미지 1/3 DeWALT Hammer Drill DW511 Power Cord Replacement: 4 단계, 이미지 2/3 DeWALT Hammer Drill DW511 Power Cord Replacement: 4 단계, 이미지 3/3
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • With sharp point tweezers, push the little metal flap up in the hole holding the wire.

    • Clamp the wire with blunt tweezers, and slowly pull the wire out.

    번역하기

  6. DeWALT Hammer Drill DW511 Power Cord Replacement: 5 단계, 이미지 1/3 DeWALT Hammer Drill DW511 Power Cord Replacement: 5 단계, 이미지 2/3 DeWALT Hammer Drill DW511 Power Cord Replacement: 5 단계, 이미지 3/3

    • With a pair of blunt nose tweezers, grab the white wire.

    • Carefully wiggle the wire loose.

    • Pull the wire slowly until it comes out.

    번역하기

  7. DeWALT Hammer Drill DW511 Power Cord Replacement: 6 단계, 이미지 1/1

    • With both wires free, the power cord is free from the trigger body.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Johnathan Murray

회원 가입일: 10/03/19

400 평판

안내서 4개 작성하였습니다

배지: 8

배지 +5개 더

팀

Eastern Washington University, Team S1-G3, Al-Hmeyrat Fall 2019 Eastern Washington University, Team S1-G3, Al-Hmeyrat Fall 2019 회원

EWU-AL-HMEYRAT-F19S1G3

3 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 3

7일 전: 5

30일 전: 22

전체 시간: 1,375