주요 콘텐츠로 건너뛰기

기기를 고치세요

수리할 권리

부품 & 도구

부품

지정된 부품이 없습니다.

  1. Before removing the battery from the laptop, make sure the power is off.
    • Before removing the battery from the laptop, make sure the power is off.

    • Push both battery locking clips outward at the same time.

  2. Slide the battery out of the laptop.
    • Slide the battery out of the laptop.

  3. Remove the four 4 mm Phillips #0 screws from the bottom of the laptop.
    • Remove the four 4 mm Phillips #0 screws from the bottom of the laptop.

  4. Carefully turn the laptop over and open the screen all the way. Locate the slot to remove the keyboard in the lower left hand corner.
    • Carefully turn the laptop over and open the screen all the way.

    • Locate the slot to remove the keyboard in the lower left hand corner.

    • Using a spudger as a lever, insert it into the slot and gently pry up.

  5. After the keyboard pops up, pull it away from the screen just enough to release the tabs.
    • After the keyboard pops up, pull it away from the screen just enough to release the tabs.

    • Don’t pull the keyboard out forcefully as there is still a ribbon attached to the laptop.

  6. Essential Electronics Toolkit

    Small Toolkit. Big Possibilities.

    Shop Toolkits

    Essential
    Electronics
    Toolkit

    Shop Toolkits
  7. Unlock the ZIF connector on the computer by pushing the two outside tabs toward the screen.
    • Unlock the ZIF connector on the computer by pushing the two outside tabs toward the screen.

  8. Remove the flexible ribbon from the ZIF connector.
    • Remove the flexible ribbon from the ZIF connector.

    • Do not pull on the ribbon to remove it from the ZIF connector.

  9. Position the laptop so that the bottom is facing upward.
    • Position the laptop so that the bottom is facing upward.

    • Remove the three 4 mm Phillips #0 screws holding the bottom of the palm rest.

  10. Return the laptop to proper position and open the screen.
    • Return the laptop to proper position and open the screen.

    • Remove the six 4 mm Phillips #0 screws holding in the palm rest.

  11. Gently lift the palm rest and rotate it outward so that the bottom is now facing up.
    • Gently lift the palm rest and rotate it outward so that the bottom is now facing up.

    • The ribbon attached to the track is short and extremely delicate. Use care when moving the palm rest.

  12. Lift up on the small ZIF connector and remove the ribbon.
    • Lift up on the small ZIF connector and remove the ribbon.

    • If the ribbon seems stuck, gently wiggle it to remove. Do not pull the ribbon with great force.

  13. Remove the 4 3 mm screws that hold the cooling fan to the system board.
    • Remove the 4 3 mm screws that hold the cooling fan to the system board.

  14. Remove the tape holding the cooling fan wires down.
    • Remove the tape holding the cooling fan wires down.

  15. Unplug the cooling fan wires from the system board by gently pulling on the hard molded plastic portion.
    • Unplug the cooling fan wires from the system board by gently pulling on the hard molded plastic portion.

    • Be careful not to damage the wires by tugging on them.

  16. Lift the cooling fan out of the laptop.
    • Lift the cooling fan out of the laptop.

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Taylor Bateman

회원 가입일: 2012년 01월 20일

93 평판

안내서 2개 작성하였습니다

Cal Poly, Team 11-20, Maness Winter 2012 Cal Poly, Team 11-20, Maness Winter 2012 회원

CPSU-MANESS-W12S11G20

4 회원들

안내서 7개 작성하였습니다

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 1

전체 시간: 1,225