주요 콘텐츠로 건너뛰기

기기를 수리하세요

수리할 권리

상점

보관됨
보관된 가이드
해당 안내서는 단지 역사적인 목적으로 보관됩니다. 최신 버전 안내서를 사용하여 수리 하십시오.
보관됨

소개

This guide show the procedure for replacing the display of the Dell XPS 13. It requires opening the back case and removing the battery and speakers. The display is hooked up to the motherboard by six separate connectors, and cannot be removed unless the laptop is open. Use this guide if have a cracked or malfunctioning Dell XPS 13 display.

  1. Remove the eight 4 mm T5 Torx screws from the bottom cover. Remove the eight 4 mm T5 Torx screws from the bottom cover.
    • Remove the eight 4 mm T5 Torx screws from the bottom cover.

  2. Use a plastic opening tool to pry open the 'XPS' flap in the middle. Use a plastic opening tool to pry open the 'XPS' flap in the middle.
    • Use a plastic opening tool to pry open the 'XPS' flap in the middle.

  3. Remove the single Phillips screw hidden beneath the flap.
    • Remove the single Phillips screw hidden beneath the flap.

  4. Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.
    • Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.

  5. Remove the bottom cover.
    • Remove the bottom cover.

  6. Pull the battery cable connector towards the battery to disconnect it from its socket. If the connector is stubborn, push a little at one side, then the other, to "walk" it out of its socket.
    • Pull the battery cable connector towards the battery to disconnect it from its socket.

    • If the connector is stubborn, push a little at one side, then the other, to "walk" it out of its socket.

    • If you have trouble walking the connector out of the socket, use the point of a spudger to gently push on the connector indent to slide the connector out.

    • Do not pull up.

    • Open the display and press the power button for five seconds to drain any remaining charge from the system.

  7. Remove the four 3 mm Phillips #0 screws located on each corner of the battery. Remove the four 3 mm Phillips #0 screws located on each corner of the battery.
    • Remove the four 3 mm Phillips #0 screws located on each corner of the battery.

  8. Pull the battery cable connector towards the battery to disconnect it from its socket. Do not pull up.
    • Pull the battery cable connector towards the battery to disconnect it from its socket.

    • Do not pull up.

  9. Peel up any tape securing the speaker cables to the battery.
    • Peel up any tape securing the speaker cables to the battery.

    • You do not need to remove the speakers, only the tape, allowing the battery to be removed out under the speaker cables.

  10. Remove the battery.
    • Remove the battery.

  11. Pull the sliding touchscreen connector gently to the right and out of the motherboard. Pull the sliding touchscreen connector gently to the right and out of the motherboard. Pull the sliding touchscreen connector gently to the right and out of the motherboard.
    • Pull the sliding touchscreen connector gently to the right and out of the motherboard.

  12. Use your fingers to remove the sliding camera connector out from the motherboard. Use your fingers to remove the sliding camera connector out from the motherboard.
    • Use your fingers to remove the sliding camera connector out from the motherboard.

  13. Pop the coaxial antenna cables up from the wireless card with the flat end of the spudger. Pop the coaxial antenna cables up from the wireless card with the flat end of the spudger.
    • Pop the coaxial antenna cables up from the wireless card with the flat end of the spudger.

  14. Using a spudger, pry up the press fit connector on the end of the left cable bundle. Gently remove the sliding cable connector from its port to the left of the fan. Gently remove the sliding cable connector from its port to the left of the fan.
    • Using a spudger, pry up the press fit connector on the end of the left cable bundle.

    • Gently remove the sliding cable connector from its port to the left of the fan.

  15. Remove the four, black 4.6 mm screws from the display mounts using a Phillips #0 screwdriver. The laptop needs to be open for the display to clear the cutouts of the bottom case, so you may find it easier to remove the screws while already in an open configuration. Remove the display assembly.
    • Remove the four, black 4.6 mm screws from the display mounts using a Phillips #0 screwdriver.

    • The laptop needs to be open for the display to clear the cutouts of the bottom case, so you may find it easier to remove the screws while already in an open configuration.

    • Remove the display assembly.

결론

To reassemble your device, follow these instructions in reverse order.

다른 6명이 해당 안내서를 완성하였습니다.

Austin Blakely

회원 가입일: 2019년 03월 11일

7,911 평판

안내서 46개 작성하였습니다

iFixit iFixit 회원

Community

135 회원들

안내서 15,109개 작성하였습니다

After disassembling the screen, how do I peel it off the metal screen cover?

Jon - 답글

I need to find out what screen model I have to buy a display controller to re-use the screen on a different project, but I’m not able to see behind the screen to find out the exact model.

Jon - 답글

댓글 쓰기

조회 통계:

24 시간 전: 17

7일 전: 97

30일 전: 462

전체 시간: 11,678