1. First: Eye Camera
    • First: Eye Camera

    • Remove initial frame (crack off)

    댓글 쓰기

  2. Remove 4 screws.
    • Remove 4 screws.

    댓글 쓰기

    • Remove cover to get to the PCB underneath

    댓글 쓰기

    • Remove two screws on the PCB.

    댓글 쓰기

    • Remove PCB from the base plastic piece.

    댓글 쓰기

    • Break base plastic piece. Cutters work well. Be careful not to snip the wire attached to the PCB.

    댓글 쓰기

    • Black mold (from 3D printer) piece attaches to the PCB with 4 screws.

    댓글 쓰기

    • Completed assembly of the eye camera.

    댓글 쓰기

    • Back of pupil camera is glued on. Remove with flat-head.

    댓글 쓰기

    • Remove the black frame on the front of the pupil camera.

    댓글 쓰기

    • Once frame is taken off the front, two screws need to be removed.

    댓글 쓰기

  3. Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    • One screw removed from the back.

    댓글 쓰기

    • Front housing comes off once the screws are removed from the frame.

    • Twist out the silver microphone.

    댓글 쓰기

    • Pull off bottom stand until it breaks off.

    댓글 쓰기

    • Remove rubber/plastic piece from the bottom

    댓글 쓰기

    • Remove four screws from under the plastic tape (removed from last step).

    댓글 쓰기

    • Bottom pops off

    댓글 쓰기

    • Separate the metal frame from the plastic assembly.

    • Avoid the cables

    댓글 쓰기

    • Take out PCB from the plastic housing.

    댓글 쓰기

    • Remove the rest of the black plastic housing.

    댓글 쓰기

    • Black plastic housing removed

    댓글 쓰기

    • Continue removing the black plastic housing surrounding the inner PCB.

    댓글 쓰기

    • PCB removed from the black plastic housing.

    댓글 쓰기

    • Autofocus assembly.

    • Remove two screws from the bottom of the auto-focus PCB.

    댓글 쓰기

    • Unscrew the lens

    댓글 쓰기

    • Take out the IR filter by using a scalpel for pulling out the lens tape.

    댓글 쓰기

    • Comparison photos of completed autofocus assembly vs in-progress autofocus assembly

    댓글 쓰기

    • IR LEDs replaced by SMD LED

    • Soldering required here (at bottom of LED to remove).

    댓글 쓰기

    • SMD LED info: Thick black line is near the positive side of the LED

    • Dark side (dot) is positive side on LED.

    댓글 쓰기

    • Insert PCB into 3d-printed frame.

    댓글 쓰기

    • Completed assembly.

    • Sugru used for nose/head rest

    댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Silas

회원 가입일: 2013년 11월 25일

291 평판

안내서 1개 작성함

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 4

지난 30일: 22

전체 시간: 553