기기를 수리하세요 커뮤니티 상점

Disassembling Canon PowerShot SD800 IS LCD Display

소개

Remove the back cover before removing LCD display.

필요한 것

  1. Disassembling Canon PowerShot SD800 IS LCD Display, Back Cover: 1 단계, 이미지 1/1

    • Remove one 2.25mm screw on the bottom.

    번역하기

  2. Disassembling Canon PowerShot SD800 IS LCD Display: 2 단계, 이미지 1/1

    • Remove two 2.25mm screws on the right side looking from the front.

    번역하기

  3. Disassembling Canon PowerShot SD800 IS LCD Display: 3 단계, 이미지 1/1

    • Remove one 4.7mm screw on the side with the AV output.

    번역하기

  4. Disassembling Canon PowerShot SD800 IS LCD Display: 4 단계, 이미지 1/1

    • Pull off the back cover.

    • The back cover tends to stick in the top corner (near the mode dial) due to a metal clip. Jiggle the cover side to side as you pull it out.

    번역하기

  6. Disassembling Canon PowerShot SD800 IS LCD Display, LCD Assembly: 5 단계, 이미지 1/1

    • Remove 2 2.4mm screws on bottom.

    번역하기

  7. Disassembling Canon PowerShot SD800 IS LCD Display: 6 단계, 이미지 1/1

    • Follow the small data cable to where it connects to the camera.

    • Lift the back white portion to unlock the cable.

    • The cable should easily slide out.

    • The connector is very fragile. Use caution when lifting the lock.

    번역하기

  8. Disassembling Canon PowerShot SD800 IS LCD Display: 7 단계, 이미지 1/1

    • Gently lift LCD display off.

    • There will be two data cables still attached to the camera. Do not break them.

    • There may be a loose strip of metal along the inner side of the LCD display for a secure fit.

    번역하기

  9. Disassembling Canon PowerShot SD800 IS LCD Display: 8 단계, 이미지 1/1

    • Follow the larger cable to where it connects to the camera.

    • Lift the front black portion of the connector to unlock the data cable.

    • The cable should easily slide out.

    • The connector is very fragile. Use caution when lifting the lock.

    번역하기

  10. Disassembling Canon PowerShot SD800 IS LCD Display, LCD Display: 9 단계, 이미지 1/1

    • Pry the LCD display out from the four metal clamps.

    번역하기

  11. Disassembling Canon PowerShot SD800 IS LCD Display: 10 단계, 이미지 1/1

    • To remove the LCD, peel the larger data cable off from the frame.

    • The LCD is glued by its data cable to the back of the LCD frame.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Jeremy Rabaino

회원 가입일: 10/10/10

135 평판

안내서 6개 작성하였습니다

배지: 7

배지 +4개 더

팀

Cal Poly, Team 20-9, Maness Fall 2010 Cal Poly, Team 20-9, Maness Fall 2010 회원

CPSU-MANESS-F10S20G9

5 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 1

전체 시간: 2,690