기기를 수리하세요 수리할 권리 상점

Disassembling Canon PowerShot SD850 IS Case Removal

작성자 Peter Tran (또 다른 기여자 5명)
  • 댓글 1
  • 즐겨찾기 2
  • 완료: 3

난이도

쉬움

단계

8

소요 시간

10 - 15 분

섹션

2

플래그

3

Inconsistent Images

일관성 없는 이미지

해당 안내서의 이미지를 전제 조건들과 더욱 일관성 있게 업데이트하는 것은 안내서의 멋짐이 향상될 것입니다.

Action Shots

액션 샷

액션 영웅이 되십시오! 해당 안내서는 특정 액션을 더 잘 보여주기 위한 사진들이 필요합니다.

Missing Prerequisites

전제 조건 누락

해당 안내서는 작업 시작 방법에 대한 정보가 없습니다. 전제 조건 안내서를 만들어 주십시오!

소개

How to remove the outer casing of your Canon PowerShot SD850 IS.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Slide the light grey tab toward the edge of the camera using your fingernail. Pull the light grey tab up to open the door. These photos do not show the camera’s memory card or battery, which should be visible inside.

    • Slide the light grey tab toward the edge of the camera using your fingernail.

    • Pull the light grey tab up to open the door.

    • These photos do not show the camera’s memory card or battery, which should be visible inside.

    편집

  2. Slide the small brown tab toward the edge of the camera using your fingernail. Let go of the brown tab when the battery pops up.

    • Slide the small brown tab toward the edge of the camera using your fingernail.

    • Let go of the brown tab when the battery pops up.

    • Grab battery and pull straight up to remove from holder.

    • When inserting the battery, orient it so that the terminals connect.

    편집

  3. Remove the following 4 screws: Two 2.8 mm Phillips #00 at the bottom of the camera.

    • Remove the following 4 screws:

    • Two 2.8 mm Phillips #00 at the bottom of the camera.

    • Two 2.75 mm Phillips #00 on the opposite side of the wrist strap.

    편집

  5. Open the A/V OUT DIGITAL flap on the side of the wrist strap. Remove the 2.75 mm Phillips #00 under the A/V OUT DIGITAL flap on the side of the wrist strap. Remove the 2.75 mm Phillips #00 under the A/V OUT DIGITAL flap on the side of the wrist strap.

    • Open the A/V OUT DIGITAL flap on the side of the wrist strap.

    • Remove the 2.75 mm Phillips #00 under the A/V OUT DIGITAL flap on the side of the wrist strap.

    편집

  6. On the bottom of the camera, use your fingernail to slide the light gray tab towards the edge of the camera. Slide light gray door and pull up to open the door.

    • On the bottom of the camera, use your fingernail to slide the light gray tab towards the edge of the camera.

    • Slide light gray door and pull up to open the door.

    • Remove the 8.35 mm Phillips #00 next to the brown tab that holds the battery.

    편집

  7. Gently pull the front cover straight out from the camera. This will expose the wiring on the front of the camera. Gently pull the front cover straight out from the camera. This will expose the wiring on the front of the camera.

    • Gently pull the front cover straight out from the camera. This will expose the wiring on the front of the camera.

    편집

  8. Remove the 2.75 mm Phillips #00 next to A/V OUT DIGITAL.

    • Remove the 2.75 mm Phillips #00 next to A/V OUT DIGITAL.

    편집

  9. Slide the back casing (with the screen protector) off to reveal the LCD and back wiring.

    • Slide the back casing (with the screen protector) off to reveal the LCD and back wiring.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 5명과 함께

Peter Tran

회원 가입일: 2010년 10월 06일

225 평판

안내서 6개 작성하였습니다

배지: 12

배지 +9개 더

팀

Cal Poly, Team 20-7, Maness Fall 2010 Cal Poly, Team 20-7, Maness Fall 2010 회원

CPSU-MANESS-F10S20G7

6 회원들

안내서 7개 작성하였습니다

댓글 한 개

의견 추가하세요

Had to exchange a battery/SD card cover on an Ixus970IS. This guide very helpful showing the way due to similar layout of the Ixus and the PS850IS! Thanx a lot! :-)

KBK Copenhagen DK

Keld Baden-Kristensen - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 1

전체 시간: 3,914