소개

Abolish the noisy bugger and put in a powerfully quiet cooling device.

부품

부품은 필요하지 않습니다.

  1. Find the battery and the battery tabs located on the bottom of the Compaq Mini. Find the battery and the battery tabs located on the bottom of the Compaq Mini.
    • Find the battery and the battery tabs located on the bottom of the Compaq Mini.

  2. Push the tabs inward and slide the battery out. Push the tabs inward and slide the battery out. Push the tabs inward and slide the battery out.
    • Push the tabs inward and slide the battery out.

  3. Find and remove the two screws on the bottom of your Compaq Mini covering the memory compartment. Note that the screws are attached to the panel.
    • Find and remove the two screws on the bottom of your Compaq Mini covering the memory compartment.

      • Note that the screws are attached to the panel.

  4. Push out side tabs.
    • Push out side tabs.

  5. Remove the rubber pads located on the corners of your Compaq Mini. There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.
    • Remove the rubber pads located on the corners of your Compaq Mini.

    • There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

  6. US$100.00 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기
  7. Unscrew all the corner screws. There are four total, one under each rubber pad. Unscrew all the corner screws. There are four total, one under each rubber pad.
    • Unscrew all the corner screws. There are four total, one under each rubber pad.

  8. Unscrew the screw for the bottom case located in the RAM compartment. Unscrew the screw for the bottom case located in the RAM compartment.
    • Unscrew the screw for the bottom case located in the RAM compartment.

  9. Remove the three screws in the silver tabs at the back of the keyboard. The red circles show where they are located at the back of the base under the screen. Remove the three screws in the silver tabs at the back of the keyboard. The red circles show where they are located at the back of the base under the screen.
    • Remove the three screws in the silver tabs at the back of the keyboard. The red circles show where they are located at the back of the base under the screen.

  10. Remove the eight screws from the plastic top cover.
    • Remove the eight screws from the plastic top cover.

  11. Pry up the top plastic cover using a spudger. Under the screen there are two tabs that need to be pushed in. Under the screen there are two tabs that need to be pushed in.
    • Pry up the top plastic cover using a spudger.

      • Under the screen there are two tabs that need to be pushed in.

  12. Careful lifting up the cover because the track pad is still attached. Remove the cable by pulling it up.
    • Careful lifting up the cover because the track pad is still attached.

    • Remove the cable by pulling it up.

  13. Remove the three screws.
    • Remove the three screws.

  14. Pull up on the tab. Pull up on the tab.
    • Pull up on the tab.

  15. Remove the two screws holding the fan in place. There is still a cable attached to the fan so be sure to pull that out as well.
    • Remove the two screws holding the fan in place.

    • There is still a cable attached to the fan so be sure to pull that out as well.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

alea

회원 가입일: 2010년 10월 06일

1,308 평판

안내서 14개 작성하였습니다

Cal Poly, Team 22-2, Maness Fall 2010 Cal Poly, Team 22-2, Maness Fall 2010 회원

CPSU-MANESS-F10S22G2

6 회원들

안내서 20개 작성하였습니다

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 11

전체 시간: 6,170