기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Disassembling General Electric Telephone 2-9710A Handset

소개

Use this guide to remove the shell of the handset

필요한 것

  1. Disassembling General Electric Telephone 2-9710A Handset, Phone Cord: 1 단계, 이미지 1/2 Disassembling General Electric Telephone 2-9710A Handset, Phone Cord: 1 단계, 이미지 2/2

    • Unplug the device before proceeding.

    • Using a plastic opening tool, remove the phone cord from the phone jack at the base of the headset.

    • To release the cable, gently press down on the top plastic tab of the connector.

    번역하기

  2. Disassembling General Electric Telephone 2-9710A Handset: 2 단계, 이미지 1/3 Disassembling General Electric Telephone 2-9710A Handset: 2 단계, 이미지 2/3 Disassembling General Electric Telephone 2-9710A Handset: 2 단계, 이미지 3/3

    • Remove the 7.5 mm screw.

    • Remove the screw cap.

    • Pull up the phone cord to remove it from the base.

    번역하기

  3. Disassembling General Electric Telephone 2-9710A Handset, Disassembling General Electric Telephone 2-9710A Handset: 3 단계, 이미지 1/2 Disassembling General Electric Telephone 2-9710A Handset, Disassembling General Electric Telephone 2-9710A Handset: 3 단계, 이미지 2/2

    • Remove the plastic cover with a Plastic Opening Tool by gently sliding the tool underneath the plastic and pry the cover off.

    번역하기

  4. Disassembling General Electric Telephone 2-9710A Handset: 4 단계, 이미지 1/1

    • Remove the paper with a Plastic Opening Tool by gently sliding the tool underneath and prying the paper away from the phone.

    번역하기

  6. Disassembling General Electric Telephone 2-9710A Handset: 5 단계, 이미지 1/2 Disassembling General Electric Telephone 2-9710A Handset: 5 단계, 이미지 2/2

    • Remove the rubber stopper with a Plastic Opening Tool by gently sliding the tool underneath and pry away from the phone.

    번역하기

  7. Disassembling General Electric Telephone 2-9710A Handset: 6 단계, 이미지 1/2 Disassembling General Electric Telephone 2-9710A Handset: 6 단계, 이미지 2/2

    • Remove the two screws.

    • Remove the 2 21mm screws by using a Philips #1 screwdriver.

    번역하기

  8. Disassembling General Electric Telephone 2-9710A Handset: 7 단계, 이미지 1/1

    • Pull apart the handset by pulling the shell away from the other half of the phone.

    번역하기

  9. Disassembling General Electric Telephone 2-9710A Handset: 8 단계, 이미지 1/2 Disassembling General Electric Telephone 2-9710A Handset: 8 단계, 이미지 2/2

    • Remove 3 screws attaching the logic board to shell.

    • Remove the 13mm screw with a Philips #1 screwdriver.

    • Remove the 2 13mm screws with washers with a Philips #1 screwdriver.

    번역하기

  10. Disassembling General Electric Telephone 2-9710A Handset: 9 단계, 이미지 1/2 Disassembling General Electric Telephone 2-9710A Handset: 9 단계, 이미지 2/2

    • Slide out the phone jack from the shell by gently lifting up the phone jack.

    번역하기

  11. Disassembling General Electric Telephone 2-9710A Handset: 10 단계, 이미지 1/1

    • Without removing the logic board completely, pivot the logic board out of shell.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 12명과 함께

Alles Rebel

회원 가입일: 09/20/12

72 평판

안내서 3개 작성하였습니다

배지: 8

배지 +5개 더

팀

Cal Poly, Team 16-59, Forte Fall 2012 Cal Poly, Team 16-59, Forte Fall 2012 회원

CPSU-FORTE-F12S16G59

4 회원들

안내서 17개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 22

전체 시간: 2,699