기기를 수리하세요 커뮤니티 상점

Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement

소개

If the motor burns up or the power switch breaks, you are going to need a whole new motor and shaft for the device, as they come as one piece. This guide will show how to dissemble and remove the motor-shaft assembly.

필요한 것

  1. Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement, Battery: 1 단계, 이미지 1/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement, Battery: 1 단계, 이미지 2/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement, Battery: 1 단계, 이미지 3/3

    • Pull back on the release tabs to disconnect the battery pack from the housing.

    • When installing a new battery, you may need to charge it before using it.

    편집

  2. Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement, Motor-Shaft Assembly: 2 단계, 이미지 1/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement, Motor-Shaft Assembly: 2 단계, 이미지 2/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement, Motor-Shaft Assembly: 2 단계, 이미지 3/3

    • Remove the two screws from the back of the device with the TR10 Torx Security screwdriver.

    • Make sure you have removed the battery before proceeding as accidentally powering-on the device while disassembling is dangerous due to the high-speed components inside.

    편집

  4. Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement: 3 단계, 이미지 1/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement: 3 단계, 이미지 2/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement: 3 단계, 이미지 3/3

    • Lift off the unscrewed plastic cover at an angle, away from the tip of the device.

    • Gently lift the cover. It won't take much force to remove it.

    편집

  5. Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement: 4 단계, 이미지 1/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement: 4 단계, 이미지 2/3 Dremel 7300 MiniMite Cordless Motor-Shaft Assembly Replacement: 4 단계, 이미지 3/3

    • Lift the tip of the motor-shaft assembly gently, then pull the assembly out.

    • The blue battery contact and the spring for the shaft lock button may pop out when you remove the motor-shaft assembly. Make sure to keep track of these pieces, as they are very small.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 5명과 함께

Michael Smith

회원 가입일: 02/10/16

175 평판

안내서 1개 작성함

배지: 7

배지 +4개 더

팀

USF Tampa, Team 3-4, Sullivan Spring 2016 USF Tampa, Team 3-4, Sullivan Spring 2016 회원

USFT-SULLIVAN-S16S3G4

4 회원들

안내서 4개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 40

전체 시간: 3,088