기기를 수리하세요 커뮤니티 상점

Drill Master Heat Gun Motor Replacement

소개

The motor inside the barrel of the gun powers the fan. Use this guide to replace the motor.

필요한 것

  1. Drill Master Heat Gun Motor Replacement, Motor: 1 단계, 이미지 1/1

    • Be sure the heat gun is unplugged before starting this process.

    • Remove the seven 14mm screws from the side of the drill using the PH#0 screwdriver.

    • You will need a screwdriver extension.

    편집

  2. Drill Master Heat Gun Motor Replacement: 2 단계, 이미지 1/1

    • Remove the 8mm screw from underside of barrel using the PH#0 screwdriver.

    • Don't try to open the casing just yet.

    편집

  3. Drill Master Heat Gun Motor Replacement: 3 단계, 이미지 1/3 Drill Master Heat Gun Motor Replacement: 3 단계, 이미지 2/3 Drill Master Heat Gun Motor Replacement: 3 단계, 이미지 3/3

    • Remove the barrel casing on either end by twisting and pulling each side off.

    편집

  4. Drill Master Heat Gun Motor Replacement: 4 단계, 이미지 1/1

    • Remove the top casing to reveal inside of drill. You might have to tug a little harder for this one.

    편집

  6. Drill Master Heat Gun Motor Replacement: 5 단계, 이미지 1/1

    • Remove the metal casing and fan cover from the fan unit.

    편집

  7. Drill Master Heat Gun Motor Replacement: 6 단계, 이미지 1/1

    • Bend the metal prongs backward that connect the fan motor to the plastic cap.

    • Bending the brackets too far back can cause the brackets to break.

    편집

  8. Drill Master Heat Gun Motor Replacement: 7 단계, 이미지 1/1

    • Remove the plastic cap from the motor,

    • This will allow you to work only with the motor and fan.

    편집

  9. Drill Master Heat Gun Motor Replacement: 8 단계, 이미지 1/1

    • Remove the fan by pulling it from the motor rod.

    편집

  10. Drill Master Heat Gun Motor Replacement: 9 단계, 이미지 1/1

    • Remove the two 12mm screws from the plastic fan casing using PH#00

    편집

  11. Drill Master Heat Gun Motor Replacement: 10 단계, 이미지 1/1

    • Remove the plastic fan casing.

    편집

  12. Drill Master Heat Gun Motor Replacement: 11 단계, 이미지 1/1

    • Remove the metal casing from the motor and insert the new motor in its place.

    • You may have to tug a little.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Mikayla Kim

회원 가입일: 01/31/17

523 평판

안내서 5개 작성하였습니다

배지: 8

배지 +5개 더

팀

University of North Texas, Team 1-2, Campbell Spring 2017 University of North Texas, Team 1-2, Campbell Spring 2017 회원

UNT-CAMPBELL-S17S1G2

3 회원들

안내서 10개 작성하였습니다

댓글 한 개

Where can I find a new motor?

jstabler38 - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 12

전체 시간: 1,444