기기를 수리하세요 커뮤니티 상점

Dyson Supersonic HD03 Hairdryer Filter Replacement

소개

A hairdryer is commonly used in our daily life, sometimes users forgot how important cleaning your device is. This guide is mainly focused on replacing and cleaning the Dyson Supersonic HD03 hairdryer filter. Whenever users encounter operation failure or weird noises, there are high chances that the hairdryer’s filter is blocked with dust or hair. Cleaning your hairdryer filter will help you avoid operation failure and increase your device life span. This guide will show you how to clean and replace your filter.

For further detailed information, you can visit Dyson Official.

필요한 것

  1. Dyson Supersonic HD03 Hairdryer Filter Replacement, Filter: 1 단계, 이미지 1/2 Dyson Supersonic HD03 Hairdryer Filter Replacement, Filter: 1 단계, 이미지 2/2

    • Unplug the hairdryer to avoid further hazard.

    편집

  2. Dyson Supersonic HD03 Hairdryer Filter Replacement: 2 단계, 이미지 1/2 Dyson Supersonic HD03 Hairdryer Filter Replacement: 2 단계, 이미지 2/2

    • Remove the dirty filter cage by twisting the filter towards the left.

    • The filter cage will be unlocked when the red dot matches the white thin circle.

    • Do not run your hairdryer without a filter cage.

    편집

  4. Dyson Supersonic HD03 Hairdryer Filter Replacement: 3 단계, 이미지 1/1

    • Soak the filter cage in dish soap and warm water for at least 30 minutes.

    • You can leave the filter in for multiple hours or overnight if it's especially dirty.

    편집

    • Use the supplied filter cleaning brush or any other cleaning tool to vigorously scrub the soaked filter cage.

    • Be sure to remove all blockages.

    편집

  6. Dyson Supersonic HD03 Hairdryer Filter Replacement: 5 단계, 이미지 1/1

    • Rinse and dry your filter cage.

    • Check that the filter cage is clean by holding it up to the light - you should be able to see light through it. If you can't, repeat the previous step.

    편집

  7. Dyson Supersonic HD03 Hairdryer Filter Replacement: 6 단계, 이미지 1/2 Dyson Supersonic HD03 Hairdryer Filter Replacement: 6 단계, 이미지 2/2

    • Insert the filter back into the filter cage and install the filter cage back onto the device.

    • The filter cage will be locked when the red dot matches the white filled circle.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 2명과 함께

Huan-Che Hsu

회원 가입일: 09/18/21

192 평판

안내서 1개 작성함

배지: 4

+1개 배지 추가

팀

York University, Team F-14, Woodhouse Fall 2021 York University, Team F-14, Woodhouse Fall 2021 회원

YORK-WOODHOUSE-F21SFG14

1 회원

안내서 1개 작성하였습니다

댓글 한 개

My Dyson hair dryer has quitting every 30 seconds - apparently overheating. It was very easy to remove the filter cage and wipe the filter clean. Problem solved!

Jimjar - 답글

댓글 쓰기

조회 통계:

24 시간 전: 4

7일 전: 9

30일 전: 61

전체 시간: 4,098