주요 콘텐츠로 건너뛰기

Etekcity Lasergrip 1080 Screen Replacement

필요한 것

  1. Etekcity Lasergrip 1080 Screen Replacement, Battery: 1 단계, 이미지 1/1
    • Pull the battery cover away from the handle by gripping near the thumb groove.

  2. Etekcity Lasergrip 1080 Screen Replacement: 2 단계, 이미지 1/1
    • Gently pull the battery out of the handle.

    • Excessive force could damage wires.

  3. Etekcity Lasergrip 1080 Screen Replacement: 3 단계, 이미지 1/2 Etekcity Lasergrip 1080 Screen Replacement: 3 단계, 이미지 2/2
    • Disconnect the battery by pulling the connector away from it.

    • Positive first

    • Negative second

    • When replacing the battery, this order is reversed.

  4. Etekcity Lasergrip 1080 Screen Replacement, Buttons: 4 단계, 이미지 1/2 Etekcity Lasergrip 1080 Screen Replacement, Buttons: 4 단계, 이미지 2/2
    • Remove the battery cover from the device by pulling it straight out.

  5. Etekcity Lasergrip 1080 Screen Replacement: 5 단계, 이미지 1/2 Etekcity Lasergrip 1080 Screen Replacement: 5 단계, 이미지 2/2
    • Using the plastic opening tool remove the front and rear yellow covers.

    • When removing the back cover, be careful not to lose the buttons as they are not connected.

  6. Etekcity Lasergrip 1080 Screen Replacement: 6 단계, 이미지 1/1
    • Remove the two 3.1 mm Phillips #0 screws.

  7. Etekcity Lasergrip 1080 Screen Replacement: 7 단계, 이미지 1/2 Etekcity Lasergrip 1080 Screen Replacement: 7 단계, 이미지 2/2
    • Pull the two halves apart.

    • Be careful not to lose any components on the inside.

  8. Etekcity Lasergrip 1080 Screen Replacement: 8 단계, 이미지 1/1
    • Realign the buttons with the button terminals.

    • Red terminal to red button.

    • Orange terminal to orange button.

    • Yellow terminal to yellow button.

  9. Etekcity Lasergrip 1080 Screen Replacement, Etekcity Lasergrip 1080 Trigger Replacement: 9 단계, 이미지 1/2 Etekcity Lasergrip 1080 Screen Replacement, Etekcity Lasergrip 1080 Trigger Replacement: 9 단계, 이미지 2/2
    • Carefully pull the trigger out.

    • The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.

    • To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

  10. Etekcity Lasergrip 1080 Screen Replacement, Screen: 10 단계, 이미지 1/1
    • Carefully pull the motherboard out of its slot in the body of the device.

  11. Etekcity Lasergrip 1080 Screen Replacement: 11 단계, 이미지 1/2 Etekcity Lasergrip 1080 Screen Replacement: 11 단계, 이미지 2/2
    • Unscrew the two 3.4 mm screws on the motherboard.

  12. Etekcity Lasergrip 1080 Screen Replacement: 12 단계, 이미지 1/1
    • Take off the cover and separate the parts.

    • All of these parts are fragile and mishandling them may cause damage.

결론

To reassemble your device, follow these instructions in reverse order.

Carlos Pineda

회원 가입일: 08/27/15

195 평판

안내서 1개 작성함

USF Tampa, Team 5-1, Blackwell Fall 2015 USF Tampa, Team 5-1, Blackwell Fall 2015 회원

USFT-BLACKWELL-F15S5G1

3 회원들

안내서 9개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 6

30일 전: 9

전체 시간: 908