기기를 수리하세요 커뮤니티 상점

Framework Laptop 16" SSD Replacement

소개

Use this guide to replace the SSD, or the storage, in your Framework 16" laptop.

The Framework 16" laptop supports two SSD slots: one "primary" M.2 2280 card and one "secondary" M.2 2230 card. The primary card sits on top of the secondary card, so you can use this guide to replace both cards.

Note: the laptop used in this guide is a generic setup of one US keyboard, one numpad module, and two touchpad spacers. Your setup might vary, but the procedure should remain the same.

필요한 것

  1. Framework Laptop 16" SSD Replacement, Before you begin: 1 단계, 이미지 1/2 Framework Laptop 16" SSD Replacement, Before you begin: 1 단계, 이미지 2/2

    • Unplug all cables and fully shut down your laptop.

    • If your repair requires a spudger, a T5 Torx, or a Phillips screwdriver, you can use the included Framework screwdriver. Whichever works best for you!

    • Framework recommends that you put your laptop into battery disconnect mode in the BIOS whenever removing the battery. Read how to do that here.

    • To disable this mode, click here.

    편집

  2. Framework Laptop 16" SSD Replacement, Unlock the Input Modules: 2 단계, 이미지 1/3 Framework Laptop 16" SSD Replacement, Unlock the Input Modules: 2 단계, 이미지 2/3 Framework Laptop 16" SSD Replacement, Unlock the Input Modules: 2 단계, 이미지 3/3

    • Use your fingernail to pull out the two Input Module latches and unlock them.

    • The latch will show red if it's unlocked.

    편집

  3. Framework Laptop 16" SSD Replacement, Remove the touchpad spacers: 3 단계, 이미지 1/3 Framework Laptop 16" SSD Replacement, Remove the touchpad spacers: 3 단계, 이미지 2/3 Framework Laptop 16" SSD Replacement, Remove the touchpad spacers: 3 단계, 이미지 3/3

    • Use your fingers to slide the touchpad spacer toward the bottom edge of the laptop and unclip it.

    • If you're having trouble, check if the corresponding Input Module latch is properly unlocked.

    • Lift the touchpad spacer off the laptop and remove it.

    편집

  4. Framework Laptop 16" SSD Replacement: 4 단계, 이미지 1/1

    • Repeat the same procedure for the other touchpad spacer.

    편집

  5. Framework Laptop 16" SSD Replacement, Remove the touchpad: 5 단계, 이미지 1/3 Framework Laptop 16" SSD Replacement, Remove the touchpad: 5 단계, 이미지 2/3 Framework Laptop 16" SSD Replacement, Remove the touchpad: 5 단계, 이미지 3/3

    • Use your fingers to slide the touchpad toward the bottom edge of the laptop and disconnect it.

    • If you're having trouble, check if the Input Module latches are properly unlocked.

    • Lift the touchpad and remove it.

    • During reassembly, perform the following:

    • Place the touchpad flat on its cutout so its clips are properly aligned.

    • Press the touchpad down and slide it into place so it lines up evenly with the bottom edge of the laptop.

    편집

  7. Framework Laptop 16" SSD Replacement, Remove the keyboard: 6 단계, 이미지 1/3 Framework Laptop 16" SSD Replacement, Remove the keyboard: 6 단계, 이미지 2/3 Framework Laptop 16" SSD Replacement, Remove the keyboard: 6 단계, 이미지 3/3

    • The keyboard is held in place with strong magnets. Apply gradually increasing force to avoid having the keyboard violently eject.

    • Grip the two pull tabs along the bottom of the keyboard.

    • Lift the pull tabs until the keyboard magnets release.

    • Remove the keyboard.

    • During reassembly, make sure the keyboard is seated properly on its alignment pegs and sits evenly with the edges of the laptop.

    편집

  8. Framework Laptop 16" SSD Replacement, Remove the numpad: 7 단계, 이미지 1/3 Framework Laptop 16" SSD Replacement, Remove the numpad: 7 단계, 이미지 2/3 Framework Laptop 16" SSD Replacement, Remove the numpad: 7 단계, 이미지 3/3

    • The numpad is held in place with strong magnets. Apply gradually increasing force to avoid having the numpad violently eject.

    • Grip the pull tab at the bottom of the numpad.

    • Lift the pull tab until the numpad magnets release.

    • Remove the numpad.

    • During reassembly, make sure the numpad is seated properly on its alignment pegs and sits flush with the edges of the laptop.

    편집

  9. Framework Laptop 16" SSD Replacement, Disconnect the midframe cable: 8 단계, 이미지 1/2 Framework Laptop 16" SSD Replacement, Disconnect the midframe cable: 8 단계, 이미지 2/2

    • Grip the black pull tab on the midframe cable press connector.

    • Lift up to disconnect the midframe cable.

    편집

  10. Framework Laptop 16" SSD Replacement, Loosen the midframe screws: 9 단계, 이미지 1/2 Framework Laptop 16" SSD Replacement, Loosen the midframe screws: 9 단계, 이미지 2/2

    • The midframe screws are ordered from 2–17 (number 1 is the press connector). You don't have to follow the order, but you can use it to help keep track of the screws you've loosened.

    • Use a T5 Torx screwdriver to loosen the 16 captive screws securing the midframe.

    • During reassembly, follow the order (starting with 2) to reinstall the screws across the midframe evenly.

    편집

  11. Framework Laptop 16" SSD Replacement, Remove the midframe: 10 단계, 이미지 1/2 Framework Laptop 16" SSD Replacement, Remove the midframe: 10 단계, 이미지 2/2

    • Use your fingernail to lift the bottom edge of the midframe enough to grip it with your fingers.

    편집

  12. Framework Laptop 16" SSD Replacement: 11 단계, 이미지 1/2 Framework Laptop 16" SSD Replacement: 11 단계, 이미지 2/2

    • Lift the midframe off the laptop and remove it.

    • During reassembly, make sure the midframe sits evenly on its alignment pegs before tightening the screws.

    편집

  13. Framework Laptop 16" SSD Replacement, Loosen the battery screws: 12 단계, 이미지 1/2 Framework Laptop 16" SSD Replacement, Loosen the battery screws: 12 단계, 이미지 2/2

    • Use a T5 Torx screwdriver to loosen the three captive screws securing the battery.

    편집

  14. Framework Laptop 16" SSD Replacement, Remove the battery: 13 단계, 이미지 1/3 Framework Laptop 16" SSD Replacement, Remove the battery: 13 단계, 이미지 2/3 Framework Laptop 16" SSD Replacement, Remove the battery: 13 단계, 이미지 3/3

    • Grip the black pull tab at the top of the battery.

    • Lift the pull tab to disconnect the battery connector.

    • Remove the battery.

    편집

  15. Framework Laptop 16" SSD Replacement, Remove the SSD screw: 14 단계, 이미지 1/2 Framework Laptop 16" SSD Replacement, Remove the SSD screw: 14 단계, 이미지 2/2

    • Use a T5 Torx screwdriver to remove the 2 mm‑long screw securing the SSD.

    • The SSD might pop up at a shallow angle when you remove the screw.

    편집

  16. Framework Laptop 16" SSD Replacement, Remove the SSD: 15 단계, 이미지 1/3 Framework Laptop 16" SSD Replacement, Remove the SSD: 15 단계, 이미지 2/3 Framework Laptop 16" SSD Replacement, Remove the SSD: 15 단계, 이미지 3/3

    • Grip the end of the SSD with the screw hole and slide it out of its socket.

    • Remove the SSD.

    • If you're installing a secondary M.2 2230 SSD, remove the 2 mm‑long screw next to the gray thermal pad and follow the same removal procedure.

    • During reassembly, insert the SSD at a shallow angle into its socket, and hold it flat to the laptop while you reinsert its screw.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers Community for help.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

Alex Diaz-Kokaisl

회원 가입일: 01/16/22

129,318 평판

안내서 600개 작성하였습니다

배지: 34

배지 +31개 더

팀

iFixit iFixit 회원

Staff

140 회원들

안내서 18,077개 작성하였습니다

댓글 한 개

Why is battery removal necessary? If machine is powered off or better yet, has internal battery disconnected via bios, this seems like an unnecessary step?

Jacob C. - 답글

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 21

30일 전: 101

전체 시간: 579