기기를 수리하세요 커뮤니티 상점

Fugoo Tough XL Bass Speaker Replacement

소개

The two bass speakers are located on the left and right ends of the Fugoo Tough XL device.

필요한 것

  1. Fugoo Tough XL Bass Speaker Replacement, Case: 1 단계, 이미지 1/1

    • Remove the four 3 mm screws located in each corner using a 3 mm Hex screwdriver.

    번역하기

  2. Fugoo Tough XL Bass Speaker Replacement: 2 단계, 이미지 1/2 Fugoo Tough XL Bass Speaker Replacement: 2 단계, 이미지 2/2

    • Gently pull up and off the outer casing.

    • Do not feel afraid to use a bit of force if necessary.

    번역하기

  3. Fugoo Tough XL Bass Speaker Replacement: 3 단계, 이미지 1/2 Fugoo Tough XL Bass Speaker Replacement: 3 단계, 이미지 2/2

    • Remove the internal device from the outer casing.

    • Remove the four 12 mm screws on each corner using a T10 Torx screwdriver.

    • Remove the eight 6 mm screws on the top and bottom using a T10 Torx screwdriver.

    번역하기

  4. Fugoo Tough XL Bass Speaker Replacement: 4 단계, 이미지 1/3 Fugoo Tough XL Bass Speaker Replacement: 4 단계, 이미지 2/3 Fugoo Tough XL Bass Speaker Replacement: 4 단계, 이미지 3/3

    • Use your hands to gently remove the side plates.

    • Use an opening tool to pry off the back plate with the Fugoo trademark.

    번역하기

  6. Fugoo Tough XL Bass Speaker Replacement: 5 단계, 이미지 1/1

    • Slowly pull the front casing from the back casing. Avoid putting any tension on the connected cables.

    • Separate the two slowly and consistently to avoid damaging the speaker cables.

    번역하기

  7. Fugoo Tough XL Bass Speaker Replacement, Motherboard: 6 단계, 이미지 1/2 Fugoo Tough XL Bass Speaker Replacement, Motherboard: 6 단계, 이미지 2/2

    • Carefully untangle the wires that connect the speaker to the motherboard.

    번역하기

  8. Fugoo Tough XL Bass Speaker Replacement: 7 단계, 이미지 1/2 Fugoo Tough XL Bass Speaker Replacement: 7 단계, 이미지 2/2
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Use tweezers to remove the two ribbon wires on the left and right side of motherboard.

    • Do not pull the cables by the cord, as this could damage the cables and the motherboard. It is best to always disconnect the cables from the base, which is closest to the motherboard, using an iFixit opening tool.

    번역하기

  9. Fugoo Tough XL Bass Speaker Replacement: 8 단계, 이미지 1/2 Fugoo Tough XL Bass Speaker Replacement: 8 단계, 이미지 2/2

    • There is a hidden ribbon on the motherboard, that becomes visible once the motherboard has been pulled out.

    • Pull the motherboard halfway out.

    • Gently unplug the ribbon using tweezers.

    번역하기

  10. Fugoo Tough XL Bass Speaker Replacement: 9 단계, 이미지 1/2 Fugoo Tough XL Bass Speaker Replacement: 9 단계, 이미지 2/2

    • Remove the motherboard and battery.

    • Remove the four 3 mm screws from the motherboard using a 3 mm Hex screwdriver.

    번역하기

  11. Fugoo Tough XL Bass Speaker Replacement, Bass Speaker: 10 단계, 이미지 1/1

    • Remove four 3 mm screws using a 3 mm Hex screwdriver.

    번역하기

  12. Fugoo Tough XL Bass Speaker Replacement: 11 단계, 이미지 1/2 Fugoo Tough XL Bass Speaker Replacement: 11 단계, 이미지 2/2

    • Pull the bass speaker from the internal case.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 5명과 함께

Austin Coats

회원 가입일: 02/17/17

107 평판

안내서 1개 작성함

배지: 7

배지 +4개 더

팀

USF Tampa, Team S19-G1, Hoffman Spring 2017 USF Tampa, Team S19-G1, Hoffman Spring 2017 회원

USFT-HOFFMAN-S17S19G1

4 회원들

안내서 5개 작성하였습니다

댓글 한 개

Hello, what is the power of this loudspeaker for resistances Ω, and RMS

Marcin Kopera - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 8

전체 시간: 772