기기를 수리하세요 커뮤니티 상점

Fujifilm Endeavor 100ix Film Door Replacement

필요한 것

  1. Fujifilm Endeavor 100ix Film Door Replacement, Outer Casing: 1 단계, 이미지 1/1

    • Locate and remove two 6.4mm screws on the bottom of the camera with a Phillips #00 screwdriver.

    번역하기

  2. Fujifilm Endeavor 100ix Film Door Replacement: 2 단계, 이미지 1/1

    • Locate the battery door.

    번역하기

  3. Fujifilm Endeavor 100ix Film Door Replacement: 3 단계, 이미지 1/1

    • Locate the latch on the battery door marked by the word "BATT." Use your finger to pry it open.

    번역하기

  4. Fujifilm Endeavor 100ix Film Door Replacement: 4 단계, 이미지 1/1

    • Remove the battery from the camera by pulling the battery door outwards.

    번역하기

  5. Fujifilm Endeavor 100ix Film Door Replacement: 5 단계, 이미지 1/1

    • Locate and remove three black 3.80mm screws on the back of the camera with the Phillips #00 screwdriver.

    번역하기

  7. Fujifilm Endeavor 100ix Film Door Replacement: 6 단계, 이미지 1/2 Fujifilm Endeavor 100ix Film Door Replacement: 6 단계, 이미지 2/2

    • Locate and remove the 6.4mm screws located on either side of the camera with a Phillips #00 screwdriver.

    번역하기

  8. Fujifilm Endeavor 100ix Film Door Replacement: 7 단계, 이미지 1/1

    • Locate the film door latch located on the side of the camera.

    • Insert the spudger under the latch.

    • Caution: Be careful during the following step in order to not break any parts within the camera. Prying the latch in any other direction than perpendicular may result in broken parts.

    • Pry the latch upward, applying force perpendicular to the camera.

    번역하기

  9. Fujifilm Endeavor 100ix Film Door Replacement: 8 단계, 이미지 1/1

    • Insert the flat edge of the spudger between the gold front casing and the black back casing.

    • Pry the spudger upward until the black back casing snaps out and is dislodged on that edge of the camera.

    번역하기

  10. Fujifilm Endeavor 100ix Film Door Replacement: 9 단계, 이미지 1/1

    • Squeeze the camera by placing a thumb on the tab marked CE.

    • Pull the back half of the camera firmly away from the camera body.

    번역하기

  11. Fujifilm Endeavor 100ix Film Door Replacement: 10 단계, 이미지 1/1

    • Locate and remove the 3.80mm screw inside the film compartment with the Phillips #00 screwdriver.

    번역하기

  12. Fujifilm Endeavor 100ix Film Door Replacement: 11 단계, 이미지 1/2 Fujifilm Endeavor 100ix Film Door Replacement: 11 단계, 이미지 2/2

    • Pull the front cover off of the camera by lifting the tripod tab over the tripod hole.

    번역하기

  13. Fujifilm Endeavor 100ix Film Door Replacement, Film Door: 12 단계, 이미지 1/1

    • Locate the film door on the bottom of the camera.

    • Locate the pin that connects the film door to the camera

    번역하기

  14. Fujifilm Endeavor 100ix Film Door Replacement: 13 단계, 이미지 1/1

    • Push the pin from one side with the spudger until it comes out on the opposite side.

    번역하기

  15. Fujifilm Endeavor 100ix Film Door Replacement: 14 단계, 이미지 1/1

    • Grab the pin with the tweezers and gently pull it out.

    • The film door should feel lose.

    번역하기

  16. Fujifilm Endeavor 100ix Film Door Replacement: 15 단계, 이미지 1/1

    • Remove the door with your fingers and discard it.

    • Insert the replacement film door appropriately to fit where the broken door was located.

    번역하기
결론

To reassemble your device, follow the instructions from the "Disassembling Fujifilm Endeavor 100ix Outer Casing" guide in reverse order.

작성자

다른 기여자 6명과 함께

Eric Nicolai

회원 가입일: 01/10/11

679 평판

안내서 6개 작성하였습니다

배지: 10

배지 +7개 더

팀

Cal Poly, Team 13-5, Forte Winter 2011 Cal Poly, Team 13-5, Forte Winter 2011 회원

CPSU-FORTE-W11S13G5

5 회원들

안내서 11개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 1

전체 시간: 1,760