주요 콘텐츠로 건너뛰기

소개

Remove that battery to avoid electrocution. The light sensor is delicate, so be cautious when removing it.

부품

지정된 부품이 없습니다.

  1. Turn the device off by pressing and holding the power button on the top left of the device.
    • Turn the device off by pressing and holding the power button on the top left of the device.

  2. Use the plastic opening tool to separate the tabs on the black back cover of the device by leveraging the tool against the frame around the perimeter of the device.
    • Use the plastic opening tool to separate the tabs on the black back cover of the device by leveraging the tool against the frame around the perimeter of the device.

  3. Once all of the tabs are popped out, take the back cover off.
    • Once all of the tabs are popped out, take the back cover off.

    • The back cover is a separate piece from the device.

  4. Using the plastic spudger, carefully remove the white tab connected to the battery from the device by pulling the tab in the opposite direction from which it is connected. Using the plastic spudger, carefully remove the white tab connected to the battery from the device by pulling the tab in the opposite direction from which it is connected.
    • Using the plastic spudger, carefully remove the white tab connected to the battery from the device by pulling the tab in the opposite direction from which it is connected.

  5. Use the plastic spudger to lift the battery up and away from the device. Do not puncture or bend the battery. Serious health complications could occur. Do not puncture or bend the battery. Serious health complications could occur.
    • Use the plastic spudger to lift the battery up and away from the device.

    • Do not puncture or bend the battery. Serious health complications could occur.

  6. Using the T5 bit, unscrew the four 5.7mm screws in the four corners of the device. Using the T5 bit, unscrew the four 5.7mm screws in the four corners of the device.
    • Using the T5 bit, unscrew the four 5.7mm screws in the four corners of the device.

  7. Leverage the plastic opening tool to pop the tabs between the black screen and the metal frame around the perimeter of the device. Do not forcibly separate the two pieces after the tabs have been popped as there are connections between the two pieces that could be torn. Do not forcibly separate the two pieces after the tabs have been popped as there are connections between the two pieces that could be torn.
    • Leverage the plastic opening tool to pop the tabs between the black screen and the metal frame around the perimeter of the device.

    • Do not forcibly separate the two pieces after the tabs have been popped as there are connections between the two pieces that could be torn.

  8. Using your fingers, pull the red and black wire from the back of the screen. Using your fingers, pull the red and black wire from the back of the screen.
    • Using your fingers, pull the red and black wire from the back of the screen.

  9. Locate the red and black wire connected to the circuit board with the round, black, rubbery disc that was connected to the other half of the device (that disc is the light sensor). Gently pull the wire up from the circuit board. Locate the red and black wire connected to the circuit board with the round, black, rubbery disc that was connected to the other half of the device (that disc is the light sensor). Gently pull the wire up from the circuit board.
    • Locate the red and black wire connected to the circuit board with the round, black, rubbery disc that was connected to the other half of the device (that disc is the light sensor). Gently pull the wire up from the circuit board.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

David

회원 가입일: 2015년 03월 11일

412 평판

안내서 3개 작성하였습니다

Colorado Springs, Team 4-1, Panko Spring 2015 Colorado Springs, Team 4-1, Panko Spring 2015 회원

UCCS-PANKO-S15S4G1

2 회원들

안내서 5개 작성하였습니다

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 5

전체 시간: 203