메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Gateway MD2614u Processor Replacement

작성자 Toni Pipes (또 다른 기여자 6명)
  • 댓글 1
  • 즐겨찾기 2
  • 완료: 1

난이도

보통

단계

9

소요 시간

5 - 10 분

섹션

3

플래그

1

Markup Mishap

마크업 사고

해당 안내서는 더 나은 마크업이 필요합니다. 일부 마크업 주석의 편집 또는 작성을 도와주십시오!

소개

You will use the fan repair guide to get to the CPU. Then, you will use the lock to remove the CPU.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Place the laptop so the back cover is facing up.

    • Place the laptop so the back cover is facing up.

    편집

  2. Remove the 8 screws from the back cover using the Phillips #00 screwdriver.

    • Remove the 8 screws from the back cover using the Phillips #00 screwdriver.

    편집

  3. Lift off the cover.

    • Lift off the cover.

    편집

  4. 아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

    아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

  5. Unplug the fan’s power cable, which is a group of black wires attached to a white plastic head on the motherboard.

    • Unplug the fan’s power cable, which is a group of black wires attached to a white plastic head on the motherboard.

    • Pull the plastic part of the cable, not the wires, so that the plug does not break.

    편집

  6. Remove the two screws located on opposite sides of the fan with a Phillips #00 screw driver.

    • Remove the two screws located on opposite sides of the fan with a Phillips #00 screw driver.

    편집

  7. The fan is permanently attached to the silver heat sink next to the RAM.

    • The fan is permanently attached to the silver heat sink next to the RAM.

    • To completely remove the parts, loosen the heat sink’s four screws with a Phillips #00 screw driver.

    • Take out the screws in the numerical order shown on the heat sink.

    편집

  8. Pull the fan and heat sink toward you at a 20 degree angle upward.

    • Pull the fan and heat sink toward you at a 20 degree angle upward.

    편집

  9. The CPU is located under the heat sink you just removed. It is a green card on a white plastic surface. There is a black lock on one side of the plastic. Rotate the CPU lock 180 degrees counterclockwise with a 3.0 mm Flathead screw driver.

    • The CPU is located under the heat sink you just removed. It is a green card on a white plastic surface. There is a black lock on one side of the plastic. Rotate the CPU lock 180 degrees counterclockwise with a 3.0 mm Flathead screw driver.

    • You will hear a click as the lock unlocks.

    편집

  10. Place your fingers on opposite edges of the green card.

    • Place your fingers on opposite edges of the green card.

    • Carefully lift the CPU upward.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 6명과 함께

Toni Pipes

회원 가입일: 2010년 10월 05일

297 평판

안내서 7개 작성하였습니다

배지: 9

배지 +6개 더

팀

Cal Poly, Team 21-31, Regan Fall 2010 Cal Poly, Team 21-31, Regan Fall 2010 회원

CPSU-REGAN-F10S21G31

4 회원들

안내서 7개 작성하였습니다

댓글 한 개

의견 추가하세요

Memory address registers and memory data registers together can represent the gateway?if can how?

Jayita Roy - 답글

댓글 쓰기

1024

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 6,718