기기를 수리하세요 커뮤니티 상점

General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement

소개

Use this guide to replace the power cable in a General Pipe Cleaners Drain Cleaner PMEBO 2016.

필요한 것

  1. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement, Reverse Switch: 1 단계, 이미지 1/1

    • Before you begin, make sure the drain cleaner is disconnected from power.

    • Use a Phillips #2 driver to remove the two screws securing the control box cover.

    편집

  2. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 2 단계, 이미지 1/1

    • Remove the control box cover.

    편집

  3. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 3 단계, 이미지 1/1

    • Use a 9/16 inch deep socket and ratchet to remove the nut securing the reverse switch.

    편집

  4. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 4 단계, 이미지 1/1

    • Remove the reverse switch guard.

    편집

  5. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 5 단계, 이미지 1/2 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 5 단계, 이미지 2/2

    • Squeeze the tabs on either side of the reverse switch connector.

    • Pull the two halves of the connector apart to disconnect it.

    • Take note of where everything is connected in the control box before disconnecting anything else.

    편집

  7. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 6 단계, 이미지 1/2 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 6 단계, 이미지 2/2

    • Pull the white cable straight off of its spade connector on the power switch diaphragm.

    편집

  8. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 7 단계, 이미지 1/2 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 7 단계, 이미지 2/2

    • Pull the black cable straight off of its spade connector on the power switch diaphragm.

    편집

  9. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 8 단계, 이미지 1/3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 8 단계, 이미지 2/3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 8 단계, 이미지 3/3

    • Slide the switch assembly down out of its hole in the control box and pull it out of the control box.

    • Be careful not to snag the switch on any cables during removal.

    편집

  10. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement, Power Cable: 9 단계, 이미지 1/3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement, Power Cable: 9 단계, 이미지 2/3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement, Power Cable: 9 단계, 이미지 3/3

    • Push in on the small tab on the side of the plastic power cable clip.

    • While holding the tab down, pull straight down on the power cable.

    • Do not remove the cable yet, it is still connected to the drain cleaner. Slide it down just enough to move the clip out of the control box.

    편집

  11. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 10 단계, 이미지 1/1

    • Use a Phillips #2 screwdriver to loosen the two screws securing the power box cover.

    • With the screws loose, slide the bottom of the cover to the right enough so the whole cover can swing down and away from the box opening.

    편집

  12. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 11 단계, 이미지 1/1

    • Use a flathead screwdriver to remove the green screw securing the green power cable wire.

    편집

  13. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 12 단계, 이미지 1/1

    • Use pliers to pull the white power cable straight off of its spade connector.

    편집

  14. General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 13 단계, 이미지 1/2 General Pipe Cleaners Drain Cleaner PMEBO 2016 Power Cable Replacement: 13 단계, 이미지 2/2

    • Feed the green power cable wire through the control box first, then carefully pull down on the entire power cable and remove it.

    • Make sure you don't snag the power cable on any wires or on the control box during removal.

    • During reassembly, feed the white wire through the control box and into the power box first, then the green wire.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 1명과 함께

Adam O'Camb

회원 가입일: 04/11/15

196,683 평판

안내서 416개 작성하였습니다

배지: 39

배지 +36개 더

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 8

30일 전: 20

전체 시간: 1,188