기기를 수리하세요 커뮤니티 상점

General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement

소개

Use this guide to replace the upper feed roller bearing in a General Pipe Cleaners Drain Cleaner PMEBO 2016.

필요한 것

  1. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement, Upper Feed Roller Bearing: 1 단계, 이미지 1/1

    • Before you begin, make sure the drain cleaner is disconnected from power.

    • Use your hand to unscrew and remove the feed pressure knob.

    편집

  2. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 2 단계, 이미지 1/1

    • Use a 1/4 inch socket wrench to remove the three bolts securing the feed roller holder plate.

    편집

  3. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 3 단계, 이미지 1/1

    • Remove the feed roller holder plate.

    편집

  5. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 4 단계, 이미지 1/1

    • Use a 3/16 inch hex wrench to remove the top swing pin.

    편집

  6. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 5 단계, 이미지 1/3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 5 단계, 이미지 2/3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 5 단계, 이미지 3/3

    • Use pliers to lift out and remove the pressure spring plate.

    • Lift out and remove the pressure spring.

    편집

  7. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 6 단계, 이미지 1/2 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 6 단계, 이미지 2/2

    • Use pliers to lift the top carrier straight up and out of the feed body.

    • During reassembly, make sure that the carrier is oriented so that its threaded hole lines up with the swing pin hole in the feed body.

    • During reassembly, clean the carrier and apply new grease before inserting it into the feed body.

    편집

  8. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 7 단계, 이미지 1/1

    • Use a 3/16 inch hex wrench to remove the feed roller shaft.

    • It may be necessary to insert a thin screwdriver or hex wrench into the top end of the carrier to help hold the carrier while you loosen the feed roller shaft.

    편집

  9. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 8 단계, 이미지 1/1

    • Remove the upper feed roller assembly, including the fiber disks on either side of it.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

Adam O'Camb

회원 가입일: 04/11/15

196,683 평판

안내서 416개 작성하였습니다

배지: 39

배지 +36개 더

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 12

전체 시간: 817