기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

GoPro Hero 3 Silver Image Sensor Replacement

필요한 것

  1. GoPro Hero 3 Silver Image Sensor Replacement, Battery: 1 단계, 이미지 1/2 GoPro Hero 3 Silver Image Sensor Replacement, Battery: 1 단계, 이미지 2/2

    • Pull back on the tab on the back of GoPro to open the battery cover.

    번역하기

  2. GoPro Hero 3 Silver Image Sensor Replacement: 2 단계, 이미지 1/1

    • Pull the battery out using the tab.

    번역하기

  3. GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: 3 단계, 이미지 1/2 GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: 3 단계, 이미지 2/2

    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

    번역하기

  5. GoPro Hero 3 Silver Image Sensor Replacement: 4 단계, 이미지 1/2 GoPro Hero 3 Silver Image Sensor Replacement: 4 단계, 이미지 2/2

    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

    번역하기

  6. GoPro Hero 3 Silver Image Sensor Replacement: 5 단계, 이미지 1/2 GoPro Hero 3 Silver Image Sensor Replacement: 5 단계, 이미지 2/2

    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

    번역하기

  7. GoPro Hero 3 Silver Image Sensor Replacement: 6 단계, 이미지 1/2 GoPro Hero 3 Silver Image Sensor Replacement: 6 단계, 이미지 2/2

    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

    번역하기

  8. GoPro Hero 3 Silver Image Sensor Replacement: 7 단계, 이미지 1/2 GoPro Hero 3 Silver Image Sensor Replacement: 7 단계, 이미지 2/2

    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    번역하기

  9. GoPro Hero 3 Silver Image Sensor Replacement: 8 단계, 이미지 1/2 GoPro Hero 3 Silver Image Sensor Replacement: 8 단계, 이미지 2/2

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

    • You should now be able to remove the image sensor by simply pulling it.

    번역하기

    Where i can buy the image sensor, and for how much

    Yudha prabowo - 답글

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Jose Villa

회원 가입일: 04/01/15

297 평판

안내서 1개 작성함

배지: 10

배지 +7개 더

팀

Cal Poly, Team 24-7, Lancaster Spring 2015 Cal Poly, Team 24-7, Lancaster Spring 2015 회원

CPSU-LANCASTER-S15S24G7

3 회원들

안내서 21개 작성하였습니다

댓글 2개

After the sensor has been replaced, does the camera need any catibration?

enrilazaro - 답글

Your pictures are really dark.

Nick Ruiz - 답글

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 2

30일 전: 5

전체 시간: 1,854