기기를 수리하세요 커뮤니티 상점

GoPro Hero 4 Black Charging Port Replacement

보관된 가이드
해당 안내서는 단지 역사적인 목적으로 보관됩니다. 최신 버전 안내서를 사용하여 수리 하십시오.

필요한 것

  1. GoPro Hero 4 Black Charging Port Replacement, Charging Port: 1 단계, 이미지 1/1

    • The first step to removing the faceplate is carefully moving the opening tool around the edge.

    • After loosening the clips on the edge, pull the faceplate off. Be aware that there is double-sided stick tape holding it on (indicated by the red arrow).

    번역하기

  2. GoPro Hero 4 Black Charging Port Replacement: 2 단계, 이미지 1/1

    • Remove the four Phillips #000 screws.

    • The screws circled in red are longer than the screw circled in orange.

    번역하기

  3. GoPro Hero 4 Black Charging Port Replacement: 3 단계, 이미지 1/1

    • Remove the camera and boards from the black plastic housing. You can use many tools to do this. We found that using the plastic opening tool may assist in the removal.

    번역하기

  4. GoPro Hero 4 Black Charging Port Replacement: 4 단계, 이미지 1/1

    • Remove the ribbon cable by simply pulling on it. This will remove it from its connection.

    • Push down on the three wires and the clip will disconnect from the motherboard.

    번역하기

  6. GoPro Hero 4 Black Charging Port Replacement: 5 단계, 이미지 1/1

    • Remove the four Phillips #000 screws.

    • Once the screws are removed and out of the way, gently remove the board. As you lift the board, the computer chip (outlined in orange) will separate from the motherboard.

    번역하기

  7. GoPro Hero 4 Black Charging Port Replacement: 6 단계, 이미지 1/1

    • Take your screwdriver with the PH000 Philips head attachment on it and remove the four screws outlined in red.

    • Just like before, just pull up on the ribbon strip and remove the connector from the motherboard.

    번역하기

  8. GoPro Hero 4 Black Charging Port Replacement: 7 단계, 이미지 1/1

    • Remove these two screws and remove the riser that is being held in by the screws.

    번역하기

  9. GoPro Hero 4 Black Charging Port Replacement: 8 단계, 이미지 1/1

    • Remove the screw holding the motherboard in place.

    • Do not attempt to remove the motherboard at this stage, as it is still attached by a ribbon cable.

    번역하기

  10. GoPro Hero 4 Black Charging Port Replacement: 9 단계, 이미지 1/1

    • At the top of the ribbon cable, there is a black clip that needs to be popped up.

    • You can use your finger to pop this up. But, a pair of needle nose tweezers might help.

    번역하기

  11. GoPro Hero 4 Black Charging Port Replacement: 10 단계, 이미지 1/1

    • Gently grab the ribbon with the needle nose tweezers and pull down. This will disconnect the ribbon from the connector.

    • Now, the motherboard can be removed. Due to the USB connector being on the motherboard, the entire board needs to be replaced.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 6명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 8명과 함께

Jonathan Campbell

회원 가입일: 09/29/15

830 평판

안내서 3개 작성하였습니다

배지: 13

배지 +10개 더

팀

IUPUI, Team 1-2, Hagerty Fall 2015 IUPUI, Team 1-2, Hagerty Fall 2015 회원

IUPUI-HAGERTY-F15S1G2

3 회원들

안내서 3개 작성하였습니다

댓글 한 개

got a part number for the USB? digikey?

hazakins - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 3

전체 시간: 4,160