기기를 수리하세요 커뮤니티 상점

Goodman Furnace Blower Motor Replacement

소개

This will serve as a walk-through in the disassembly and repair of a blower motor for any Goodman branded home furnace.

필요한 것

  1. Goodman Furnace Blower Motor Replacement, Opening the Unit: 1 단계, 이미지 1/3 Goodman Furnace Blower Motor Replacement, Opening the Unit: 1 단계, 이미지 2/3 Goodman Furnace Blower Motor Replacement, Opening the Unit: 1 단계, 이미지 3/3

    • Ensure all power cables are disconnected from the unit and/or wall prior to attempting this guide.

    • Gloves are highly recommended to avoid injuries from any sharp edges.

    • Unscrew the two screws located on the rear side of the unit.

    • Remove the doors and set them aside.

    • A 3/8" screwdriver will be the easiest method of completing this step.

    편집

  2. Goodman Furnace Blower Motor Replacement, Removing Electrical Connections: 2 단계, 이미지 1/3 Goodman Furnace Blower Motor Replacement, Removing Electrical Connections: 2 단계, 이미지 2/3 Goodman Furnace Blower Motor Replacement, Removing Electrical Connections: 2 단계, 이미지 3/3

    • It is strongly advised that you take a picture of the wire configuration prior to removal for reference when connecting the new motor.

    • Disconnect the brown wire from the top of the motor.

    • Disconnect the second brown wire from the bottom of the unit.

    • Remove the white, blue, red, orange, and black wires from the controller board.

    편집

  3. Goodman Furnace Blower Motor Replacement, Removing the Motherboard Screws: 3 단계, 이미지 1/2 Goodman Furnace Blower Motor Replacement, Removing the Motherboard Screws: 3 단계, 이미지 2/2

    • Unscrew both screws connected the motherboard to the cylindrical motor container.

    • The screws are located on top and bottom sides of the plate holding the motherboard.

    편집

  5. Goodman Furnace Blower Motor Replacement, Removing the Motor Container: 4 단계, 이미지 1/2 Goodman Furnace Blower Motor Replacement, Removing the Motor Container: 4 단계, 이미지 2/2

    • Unscrew the cylindrical motor housing from the unit.

    • There are two screws located at each side of the top corner of the container.

    • Grab the motor container with two hands and pull it out of the unit.

    • Place the motherboard to the side.

    편집

  6. Goodman Furnace Blower Motor Replacement, Removing the Motor from the Housing: 5 단계, 이미지 1/3 Goodman Furnace Blower Motor Replacement, Removing the Motor from the Housing: 5 단계, 이미지 2/3 Goodman Furnace Blower Motor Replacement, Removing the Motor from the Housing: 5 단계, 이미지 3/3

    • Turn the motor container on its side, with the wires pointing up.

    • Unscrew the 3 screws attaching the motor to the housing.

    • Take the yellow wire out of the screw.

    • Use a wrench to remove the bolt from the shaft of the motor, located on the opposite side.

    • If rust has accumulated on the motor shaft, you may wish to use sandpaper to remove it to make the motor easier to remove.

    • Firmly grasp the motor from the side where the screws were previously located and pull to remove it.

    • The white label on the side of the motor contains the model number of the blower motor which you may use as a reference when ordering a replacement, if necessary.

    편집

  7. Goodman Furnace Blower Motor Replacement, Inserting the Replacement Motor: 6 단계, 이미지 1/2 Goodman Furnace Blower Motor Replacement, Inserting the Replacement Motor: 6 단계, 이미지 2/2

    • Insert the new motor into the motor housing.

    • Ensure the wires are at the front of the assembly.

    • Tighten the bolt at the shaft of the motor that you removed in the previous step.

    • You may wish to get the bolt started with your hands, and finish tightening with the wrench.

    • Ensure the flat surface is aligned with the screw hole prior to tightening with the wrench.

    편집

  8. Goodman Furnace Blower Motor Replacement, Reassembly Tips: 7 단계, 이미지 1/1

    • Ensure the fan blades are freely spinning prior to continuing.

    • When assessing the fan blade, ensure you either keep your hands flat or wear gloves to avoid injury.

    • Utilize your reference photo when rewiring the unit.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 1명과 함께

Ryan W

회원 가입일: 11/30/23

145 평판

안내서 1개 작성함

배지: 1

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 5

7일 전: 21

30일 전: 96

전체 시간: 403