주요 콘텐츠로 건너뛰기

소개

This guide will demonstrate how to clean or replace the strummer (strum bar) for a Guitar Hero: World Tour Controller.

The strummer can often become sluggish or stuck from wear and tear over time. This can often be solved by simply cleaning or lubricating the strum bar, or by replacing it entirely if damaged.

Two AA batteries will need to be removed as shown in the guide.

  1. Guitar Hero World Tour Guitar Strummer Replacement, Strummer: 1 단계, 이미지 1/3 Guitar Hero World Tour Guitar Strummer Replacement, Strummer: 1 단계, 이미지 2/3 Guitar Hero World Tour Guitar Strummer Replacement, Strummer: 1 단계, 이미지 3/3
    • Remove the battery cover.

    • Remove the two AA batteries.

  2. Guitar Hero World Tour Guitar Strummer Replacement: 2 단계, 이미지 1/3 Guitar Hero World Tour Guitar Strummer Replacement: 2 단계, 이미지 2/3 Guitar Hero World Tour Guitar Strummer Replacement: 2 단계, 이미지 3/3
    • Move the switch from "Locked" to the "Unlocked" position.

    • Remove the neck from the body of the guitar.

    • This will likely take two hands.

  3. Guitar Hero World Tour Guitar Strummer Replacement: 3 단계, 이미지 1/3 Guitar Hero World Tour Guitar Strummer Replacement: 3 단계, 이미지 2/3 Guitar Hero World Tour Guitar Strummer Replacement: 3 단계, 이미지 3/3
    • Ensure the face-plate lock is in the "Unlocked" position.

    • Pry the face plate off of the body by gently prying with an opening tool near the marked locations. The face plate should not be difficult to remove.

    • You can pry the face plate away with your fingers, or with any plastic/wooden tool.

    • Avoid using metal tools to pry the plastic face plate away, as it can lead to marring the plastic and ruining the finish.

  4. Guitar Hero World Tour Guitar Strummer Replacement: 4 단계, 이미지 1/3 Guitar Hero World Tour Guitar Strummer Replacement: 4 단계, 이미지 2/3 Guitar Hero World Tour Guitar Strummer Replacement: 4 단계, 이미지 3/3
    • Remove the eleven Torx T10 screws.

    • Remove the four Phillips #0 screws.

    • There is an additional Torx T10 screw located behind the "Warranty Void" sticker.

    • Separate the two halves of the guitar body.

  5. Guitar Hero World Tour Guitar Strummer Replacement: 5 단계, 이미지 1/3 Guitar Hero World Tour Guitar Strummer Replacement: 5 단계, 이미지 2/3 Guitar Hero World Tour Guitar Strummer Replacement: 5 단계, 이미지 3/3
    • Disconnect the ribbon cable connecting the strummer circuit board to the main control board.

    • Remove the eight Phillips #0 screws holding the strummer circuit board to the body.

    • Ensure that the switches have a solid clicking action.

    • Debris can often block the switches from actuating.

  6. Guitar Hero World Tour Guitar Strummer Replacement: 6 단계, 이미지 1/3 Guitar Hero World Tour Guitar Strummer Replacement: 6 단계, 이미지 2/3 Guitar Hero World Tour Guitar Strummer Replacement: 6 단계, 이미지 3/3
    • Remove four Phillips #0 screws holding the strum bar assembly.

    • Remove the strum bar assembly from the body. Ensure that both springs are present and in good condition.

    • Check the joint between the strum bar and its mounting brackets. Ensure there are no foreign objects jamming the hole. Ensure the joint is well lubricated.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Daniel Koelzer

회원 가입일: 2021년 09월 30일

157 평판

안내서 1개 작성함

Team

University of North Texas, Team 2-8, Raign Fall 2021 University of North Texas, Team 2-8, Raign Fall 2021 회원

UNT-RAIGN-F21S2G8

2 회원들

안내서 2개 작성하였습니다

One Comment

Great guide! Helped me find some loose screws that fixed the strumming when tightened.

Only note is that my controller uses Torx T6 screws instead of Phillips #0 screws. From info online, it looks like these controllers can have either type.

Nicholas Stecyna - 답글

댓글 쓰기

조회 통계:

24 시간 전: 12

7일 전: 88

30일 전: 347

전체 시간: 2,577