주요 콘텐츠로 건너뛰기

소개

The SSD can become worn out due to the constant reading and writing of data. As a result, it's important to know how to upgrade or replace it. This guide will explain how to replace the SSD card for the HP Elite x2 1012 G2.

  1. Make sure the device is turned off before starting.
    • Make sure the device is turned off before starting.

    • Orient the device so the back is facing you, with the kickstand up.

  2. Remove the six 3mm Torx T5 screws underneath the kickstand. Remove the six 3mm Torx T5 screws underneath the kickstand. Remove the six 3mm Torx T5 screws underneath the kickstand.
    • Remove the six 3mm Torx T5 screws underneath the kickstand.

  3. Turn the device over so the screen is facing you. Place a suction cup firmly onto a corner of the screen.
    • Turn the device over so the screen is facing you.

    • Place a suction cup firmly onto a corner of the screen.

    • Lift up gently until you see the screen separate from the casing.

    • Repeat this process for all four corners.

  4. Lift the screen up and off of the device.
    • Lift the screen up and off of the device.

    • Pry each corner up first, otherwise you may damage or crack the screen.

  5. Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently. Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently. Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently.
    • Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently.

  6. Remove the screen by gently lifting it off of the device. Remove the screen by gently lifting it off of the device.
    • Remove the screen by gently lifting it off of the device.

  7. Orient the device so that the battery is closest to you.
    • Orient the device so that the battery is closest to you.

    • The battery is the large, black rectangle at the bottom of the device.

  8. Remove  the single Phillips M2.0x2.0 screw on the SSD using a Phillips screwdriver. Turn the screwdriver counterclockwise to remove the screw. Remove  the single Phillips M2.0x2.0 screw on the SSD using a Phillips screwdriver. Turn the screwdriver counterclockwise to remove the screw.
    • Remove the single Phillips M2.0x2.0 screw on the SSD using a Phillips screwdriver. Turn the screwdriver counterclockwise to remove the screw.

  9. Gently pull the SSD to the left and up to remove it from the device. Gently pull the SSD to the left and up to remove it from the device.
    • Gently pull the SSD to the left and up to remove it from the device.

결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

Hunter Lane

회원 가입일: 2018년 04월 18일

142 평판

안내서 1개 작성함

Cal Poly, Team S18-G5, Livingston Spring 2018 Cal Poly, Team S18-G5, Livingston Spring 2018 회원

CPSU-LIVINGSTON-S18S18G5

4 회원들

안내서 10개 작성하였습니다

Vielen Dank für die sehr gute Anleitung. Es hat alles perfekt geklappt.

Das Display selber sitzt zum Teil aber sehr fest im Gehäuse und man muss sich überwinden etwas Kraft anzuwenden.

Sollte man zu fest ziehen (und einem das Display entgegenspringt) besteht ja die Gefahr die filigranen Kabel abzureißen.

Andreas Gerl - 답글

댓글 쓰기

조회 통계:

24 시간 전: 11

7일 전: 74

30일 전: 360

전체 시간: 4,289