Skip to main content

소개

The scanner piece is a part of the printer that scans over a paper. It may become misaligned or damaged over time. This guide will help a user replace the scanning piece.

  1. Open the cartridge access area.
    • Open the cartridge access area.

  2. Remove the three 11.5 mm screws with a T10 bit.
    • Remove the three 11.5 mm screws with a T10 bit.

  3. Locate the cover hinge on the right side of the printer. Pull the hinge off of the scanner to allow the scanner to open to 90 degress. Pull the hinge off of the scanner to allow the scanner to open to 90 degress.
    • Locate the cover hinge on the right side of the printer.

    • Pull the hinge off of the scanner to allow the scanner to open to 90 degress.

  4. 안드로이드 수리 키트

    새 스크린 혹은 배터리는 단 하나의 키트로 충분합니다.

    지금 장보기

    안드로이드 수리 키트

    새 스크린 혹은 배터리는 단 하나의 키트로 충분합니다.

    지금 장보기
  5. Remove the  12 mm screws on the left side of the printer with a T10 bit. Remove the  12 mm screws on the left side of the printer with a T10 bit.
    • Remove the 12 mm screws on the left side of the printer with a T10 bit.

  6. Remove the 11.5 mm screw with a T10 bit to release the spring-loaded hinge. Since this is a compression spring, the hinge will snap downwards as soon as it is loosened.
    • Remove the 11.5 mm screw with a T10 bit to release the spring-loaded hinge.

    • Since this is a compression spring, the hinge will snap downwards as soon as it is loosened.

  7. Pull the plastic side cover off of the printer. You may need to lift the printer and push the cover downwards as it is latched onto the bottom of the printer. Plastic opening tools or a metal spudger may also be used.
    • Pull the plastic side cover off of the printer.

    • You may need to lift the printer and push the cover downwards as it is latched onto the bottom of the printer.

    • Plastic opening tools or a metal spudger may also be used.

  8. Remove the five 11.5 mm screws located at the bottom of the scanner.
    • Remove the five 11.5 mm screws located at the bottom of the scanner.

    • Steps 3-6 were intended to create easier access to these screws. However, they will still be difficult to reach.

    • The top of the scanner will now easily pull off.

  9. Pry the old scanning glass up with a metal spudger. There are adhesives under the scanning glass. Be careful not to break the glass while removing it.
    • Pry the old scanning glass up with a metal spudger.

    • There are adhesives under the scanning glass. Be careful not to break the glass while removing it.

  10. The scanning piece is located in the bottom half of the scanner that was not separated from the printer. Lift the scanning piece and detach the  ribbon cable by gently pulling on it. Lift the scanning piece and detach the  ribbon cable by gently pulling on it.
    • The scanning piece is located in the bottom half of the scanner that was not separated from the printer.

    • Lift the scanning piece and detach the ribbon cable by gently pulling on it.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Ryan Steakley

회원 가입일: 2018년 01월 23일

766 Reputation

안내서 5개 작성하였습니다

Cal Poly, Team S1-G6, Livingston Winter 2018 Cal Poly, Team S1-G6, Livingston Winter 2018 회원

CPSU-LIVINGSTON-W18S1G6

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

View Statistics:

Past 24 Hours: 0

Past 7 Days: 3

Past 30 Days: 10

All Time: 240