주요 콘텐츠로 건너뛰기

소개

If your HP Spectre x360 13-ac023dx laptop will not boot up after troubleshooting possibles errors, use this motherboard replacement guide.

부품

지정된 부품이 없습니다.

  1. Flip the laptop over so the model sticker faces the ceiling. Flip the laptop over so the model sticker faces the ceiling.
    • Flip the laptop over so the model sticker faces the ceiling.

  2. Use a Torx #5 screwdriver to remove the six 3.5 mm screws holding the back cover to  the laptop. Use a Torx #5 screwdriver to remove the six 3.5 mm screws holding the back cover to  the laptop. Use a Torx #5 screwdriver to remove the six 3.5 mm screws holding the back cover to  the laptop.
    • Use a Torx #5 screwdriver to remove the six 3.5 mm screws holding the back cover to the laptop.

  3. Use the Phillips #000  screwdriver to remove the four 3.5 mm screws holding the battery. After removing the screws, detach the battery wire from the mother board with the iFixit opening tool.
    • Use the Phillips #000 screwdriver to remove the four 3.5 mm screws holding the battery.

    • After removing the screws, detach the battery wire from the mother board with the iFixit opening tool.

    • Then, carefully lift the battery off with the iFixit opening tool.

  4. Locate the Cooling Fan in the device.
    • Locate the Cooling Fan in the device.

  5. Use the Phillips #000 screwdriver  to  remove the 3mm screws holding the fan in place. Remove the wires connecting to the motherboard, using the iFixit opening tool.
    • Use the Phillips #000 screwdriver to remove the 3mm screws holding the fan in place.

    • Remove the wires connecting to the motherboard, using the iFixit opening tool.

    • The iFixit Opening Tool is not required, but recommended

  6. Remove the Cooling Fan.
    • Remove the Cooling Fan.

  7. Locate the WiFi card.
    • Locate the WiFi card.

  8. Use the Phillips #000  screwdriver to remove the screw holding the wifi card in place.
    • Use the Phillips #000 screwdriver to remove the screw holding the wifi card in place.

  9. Once the screw is removed, raise the WiFi card and slide it out from the motherboard. Once the screw is removed, raise the WiFi card and slide it out from the motherboard.
    • Once the screw is removed, raise the WiFi card and slide it out from the motherboard.

  10. Ensure that all other components  which were previously removed are not longer attached.
    • Ensure that all other components which were previously removed are not longer attached.

  11. Disconnect the wires which connect the motherboard  to  the rest of the components. The  black and red wire can be removed by pulling the wire upwards. The  black and red wire can be removed by pulling the wire upwards.
    • Disconnect the wires which connect the motherboard to the rest of the components.

    • The black and red wire can be removed by pulling the wire upwards.

  12. Use the Phillips #000 screwdriver to remove the three 3.5 mm screws which keep the motherboard in place. Use the Phillips #000 screwdriver to remove the three 3.5 mm screws which keep the motherboard in place. Use the Phillips #000 screwdriver to remove the three 3.5 mm screws which keep the motherboard in place.
    • Use the Phillips #000 screwdriver to remove the three 3.5 mm screws which keep the motherboard in place.

  13. Carefully lift and remove the motherboard. Carefully lift and remove the motherboard.
    • Carefully lift and remove the motherboard.

결론

To reassemble your device, follow these instructions in reverse order.

Jonathan

회원 가입일: 2019년 10월 21일

474 평판

안내서 4개 작성하였습니다

UMass Dartmouth, Team S1-G6, Botvin Fall 2019 UMass Dartmouth, Team S1-G6, Botvin Fall 2019 회원

UMASSD-BOTVIN-F19S1G6

3 회원들

안내서 6개 작성하였습니다

댓글 한 개

Can I get ho spectre x360 motherboard to buy from your end?

Immanuel - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 45

전체 시간: 2,009