기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

HP TouchPad Motherboard Assembly Replacement

단지 전제 조건
이 안내서는 다른 가이드의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

소개

Prerequisite only.

필요한 것

  1. HP TouchPad Motherboard Assembly Replacement, Motherboard Assembly: 1 단계, 이미지 1/1

    • If present, remove the two pieces of tape boxed in red.

    번역하기

  2. HP TouchPad Motherboard Assembly Replacement: 2 단계, 이미지 1/2 HP TouchPad Motherboard Assembly Replacement: 2 단계, 이미지 2/2

    • Use the edge of a plastic opening tool to flip up the retaining flap on the volume control/power button ribbon cable socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    • Pull the cable out of its socket.

    번역하기

  3. HP TouchPad Motherboard Assembly Replacement: 3 단계, 이미지 1/1

    • Use a plastic opening tool to lift the camera connector up and out of its socket on the motherboard.

    • Bend the camera cable away from the motherboard.

    번역하기

  4. HP TouchPad Motherboard Assembly Replacement: 4 단계, 이미지 1/2 HP TouchPad Motherboard Assembly Replacement: 4 단계, 이미지 2/2

    • Carefully flip up the retaining flap on the microphone cable socket.

    • Be sure you are prying up on the hinged retaining flap.

    • Pull the microphone cable out of its socket.

    번역하기

  5. HP TouchPad Motherboard Assembly Replacement: 5 단계, 이미지 1/1

    • Use your plastic opening tool to pry the upper antenna connector up from its socket on the motherboard.

    번역하기

  7. HP TouchPad Motherboard Assembly Replacement: 6 단계, 이미지 1/2 HP TouchPad Motherboard Assembly Replacement: 6 단계, 이미지 2/2

    • Pry up the retaining flap on the headphone jack ribbon cable socket.

    • Be sure you are prying up on the hinged retaining flap.

    • Pull the headphone jack ribbon cable out of its socket.

    번역하기

  8. HP TouchPad Motherboard Assembly Replacement: 7 단계, 이미지 1/1

    • Pry the speaker cable connector up from its socket on the motherboard.

    • Pry up from beneath the wires.

    번역하기

  9. HP TouchPad Motherboard Assembly Replacement: 8 단계, 이미지 1/2 HP TouchPad Motherboard Assembly Replacement: 8 단계, 이미지 2/2

    • Use a plastic opening tool to flip up the retaining flap on the digitizer board ribbon cable socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    • Pull the digitizer ribbon cable out of its socket.

    번역하기

  10. HP TouchPad Motherboard Assembly Replacement: 9 단계, 이미지 1/1

    • Pry up the lower antenna cable connector from its socket on the motherboard.

    번역하기

  11. HP TouchPad Motherboard Assembly Replacement: 10 단계, 이미지 1/1

    • De-route the lower antenna cable along the top edge of the battery and carefully pull it out from under its retaining clip near the top right corner of the battery.

    번역하기

  12. HP TouchPad Motherboard Assembly Replacement: 11 단계, 이미지 1/1

    • Remove the eight 3.2 mm Phillips screws securing both the battery and the motherboard to the rear case.

    번역하기

  13. HP TouchPad Motherboard Assembly Replacement: 12 단계, 이미지 1/2 HP TouchPad Motherboard Assembly Replacement: 12 단계, 이미지 2/2

    • Use a plastic opening tool to pry the battery up from the tape securing it to the rear case.

    • It is easiest to pry up along the edges of the battery closest to the USB connector and the digitizer board.

    번역하기

  14. HP TouchPad Motherboard Assembly Replacement: 13 단계, 이미지 1/1

    • Lift the motherboard assembly out of the rear case, minding any cables that may get caught.

    번역하기

  15. HP TouchPad Motherboard Assembly Replacement: 14 단계, 이미지 1/2 HP TouchPad Motherboard Assembly Replacement: 14 단계, 이미지 2/2

    • Carefully pull the battery away from the L-shaped motherboard to disconnect its cable.

    • Remove the battery from the motherboard.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Andrew Bookholt

586,239 평판

안내서 619개 작성하였습니다

배지: 47

배지 +44개 더

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 981