메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

HP iPAQ H2200 motherbaord replacement

작성자 Tyler Andrews (또 다른 기여자 8명)
  • 댓글 0
  • 즐겨찾기 3
  • 완료: 3

난이도

보통

단계

11

소요 시간

15 분

섹션

2

플래그

0

소개

The purpose of this guide is to instruct the reader on how to remove the main board of their HP iPAQ H2200 device.

도구

해당 도구 구매

부품

부품은 필요하지 않습니다.

  1. Press and slide the battery cover tab to remove battery cover.

    • Press and slide the battery cover tab to remove battery cover.

    편집

  2. Pull on the black tab to lift the battery out of the battery compartment. Pull on the black tab to lift the battery out of the battery compartment.

    • Pull on the black tab to lift the battery out of the battery compartment.

    편집

  3. Remove the stylus by sliding it out of the slot.

    • Remove the stylus by sliding it out of the slot.

    편집

  4. Remove the CF card by sliding it out of the slot at the top of the device.

    • Remove the CF card by sliding it out of the slot at the top of the device.

    편집

  5. US$100.00 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기

  6. Press down and push the black side strips toward the top of the device to remove them.

    • Press down and push the black side strips toward the top of the device to remove them.

    편집

  7. Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.

    • Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.

    편집

  8. Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side). Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).

    • Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).

    편집

  9. Open the LCD connector, where the orange strip attaches to the main board.

    • Open the LCD connector, where the orange strip attaches to the main board.

    편집

  10. Carefully remove the orange LCD strip from the connector.

    • Carefully remove the orange LCD strip from the connector.

    편집

  11. Unscrew the 2 screws located at each top corner of the main board.

    • Unscrew the 2 screws located at each top corner of the main board.

    편집

  12. Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.

    • Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 8명과 함께

Tyler Andrews

회원 가입일: 2010년 01월 13일

191 평판

안내서 5개 작성하였습니다

배지: 6

배지 +3개 더

팀

Cal Poly, Team 4-12, Forte Winter 2010 Cal Poly, Team 4-12, Forte Winter 2010 회원

CPSU-FORTE-W10S4G12

3 회원들

안내서 5개 작성하였습니다

댓글 0개

의견 추가하세요
조회 통계:

지난 24시간: 1

지난 7일: 1

지난 30일: 3

전체 시간: 4,304