기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

HP iPAQ H3850 Speaker

필요한 것

  1. HP iPAQ H3850 Speaker, Speaker: 1 단계, 이미지 1/1

    • To begin the disassembly of the device, place it on a flat surface with the screen facing down.

    번역하기

  2. HP iPAQ H3850 Speaker: 2 단계, 이미지 1/1

    • Remove the four screws found on the back cover of the device.

    번역하기

  3. HP iPAQ H3850 Speaker: 3 단계, 이미지 1/1

    • Carefully remove the back cover using a plastic opening tool against the grooves along the sides of the iPAQ.

    번역하기

  4. HP iPAQ H3850 Speaker: 4 단계, 이미지 1/1

    • Using the plastic opening tool, carefully detach the yellow ribbon from the connector pins to separate the device into two halves. (This step isn't necessary for speaker removal it will just make the process a lot easier.)

    번역하기

  6. HP iPAQ H3850 Speaker: 5 단계, 이미지 1/1

    • Remove ribbon cable connected to display logic board by pulling plastic clips on both sides towards top of device

    • Use plastic opening tool to carefully pull brown ribbon cable from connector

    번역하기

  7. HP iPAQ H3850 Speaker: 6 단계, 이미지 1/3 HP iPAQ H3850 Speaker: 6 단계, 이미지 2/3 HP iPAQ H3850 Speaker: 6 단계, 이미지 3/3

    • Use plastic opening tool to carefully remove display logic board from housing.

    • Unplug connector from the opposite end of the display logic board.

    • Completely remove component.

    번역하기

  8. HP iPAQ H3850 Speaker: 7 단계, 이미지 1/1

    • Flip up black plastic clip on large ribbon cable connector located towards center of mother board

    • Use plastic opening tool to carefully remove ribbon cable from connector

    번역하기

  9. HP iPAQ H3850 Speaker: 8 단계, 이미지 1/1

    • Gently pry clear/grey ribbon cable in the bottom corner of the device out of connector with plastic opening tool

    • Use hands or tweezers to remove if necessary

    번역하기

  10. HP iPAQ H3850 Speaker: 9 단계, 이미지 1/1

    • Use hands to gently unplug speaker and microphone connectors from mother board

    번역하기

  11. HP iPAQ H3850 Speaker: 10 단계, 이미지 1/1

    • Remove four small screws from each corner of the motherboard using phillips head screwdriver.

    • Use your hands/plastic opening tool to carefully lift the mother board out of housing.

    • Place the motherboard to the side.

    번역하기

  12. HP iPAQ H3850 Speaker: 11 단계, 이미지 1/3 HP iPAQ H3850 Speaker: 11 단계, 이미지 2/3 HP iPAQ H3850 Speaker: 11 단계, 이미지 3/3

    • At the top of the device remove the screws holding down the speaker and housing.

    • When the screws are out pry out speaker along with the housing.

    • Lay down the speaker and housing with the housing on the bottom side and pry out the speaker with the plastic opening tool.

    번역하기

    • Insert replacement speakers as needed.

    • Follow steps in reverse order to reassemble the device.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 5명과 함께

Kevin Oriz

회원 가입일: 04/07/15

101 평판

안내서 1개 작성함

배지: 4

+1개 배지 추가

팀

Eastern Washington University, Team 1-3, Plummer Spring 2015 Eastern Washington University, Team 1-3, Plummer Spring 2015 회원

EWU-PLUMMER-S15S1G3

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 3

30일 전: 3

전체 시간: 177