Skip to main content

소개

Has your HTC Desire 610 stopped charging and you know it's not a battery or charging cord issue? Follow these steps to replace a faulty charging port in an HTC Desire 610. In this guide you will learn how to take off the back, unscrew the circuit cover, and safely take out the charging port to replace with a new one.

  1. Using a plastic opening tool, take off the back cover of the phone. Using a plastic opening tool, take off the back cover of the phone. Using a plastic opening tool, take off the back cover of the phone.
    • Using a plastic opening tool, take off the back cover of the phone.

  2. Remove the four black 4mm torx screws using the Torx T5 bit.
    • Remove the four black 4mm torx screws using the Torx T5 bit.

  3. Remove the four silver 5mm torx head screws using the Torx T5 screwdriver.
    • Remove the four silver 5mm torx head screws using the Torx T5 screwdriver.

  4. Remove the two 2.5mm phillips head screws using the Phillips 000 screwdriver.
    • Remove the two 2.5mm phillips head screws using the Phillips 000 screwdriver.

  5. 아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

    아이폰 배터리 수리 키트

    Only $29.99

    Buy Now
  6. Remove the black plastic circuit cover using a plastic opening tool.
    • Remove the black plastic circuit cover using a plastic opening tool.

  7. Remove the 4mm black Torx screw using a Torx T5 screwdriver.
    • Remove the 4mm black Torx screw using a Torx T5 screwdriver.

  8. Using a pair of tweezers, disconnect the antenna wire.
    • Using a pair of tweezers, disconnect the antenna wire.

  9. Peel back the gray adhesive strip using the precision tweezers. Peel back the gray adhesive strip using the precision tweezers. Peel back the gray adhesive strip using the precision tweezers.
    • Peel back the gray adhesive strip using the precision tweezers.

  10. Pull up on the white strip so it sits 90 degrees using a pair of precision tweezers.
    • Pull up on the white strip so it sits 90 degrees using a pair of precision tweezers.

  11. Pry up the circuit board and pull it out using a pair of precision tweezers. Pry up the circuit board and pull it out using a pair of precision tweezers. Pry up the circuit board and pull it out using a pair of precision tweezers.
    • Pry up the circuit board and pull it out using a pair of precision tweezers.

  12. Remove the loud speaker using a pair of precision tweezers. The loud speaker is attached with adhesive and may require more force than expected to remove. The prongs on the speaker should be sticking up towards the top of the phone when you put the speaker on the new circuit board.
    • Remove the loud speaker using a pair of precision tweezers.

    • The loud speaker is attached with adhesive and may require more force than expected to remove.

    • The prongs on the speaker should be sticking up towards the top of the phone when you put the speaker on the new circuit board.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Kaycee Hammond

회원 가입일: 2017년 02월 11일

249 평판

안내서 2개 작성하였습니다

IUPUI, Team S1-G1, Wilson Spring 2017 IUPUI, Team S1-G1, Wilson Spring 2017 회원

IUPUI-WILSON-S17S1G1

4 회원들

안내서 3개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 4

지난 30일: 19

전체 시간: 815