기기를 수리하세요 커뮤니티 상점

Hipstreet Titan 2 HD Speaker Replacement

소개

Use this guide to replace the speaker. First you'll need to remove the rear cover. This can be a difficult process.

필요한 것

  1. Hipstreet Titan 2 HD Speaker Replacement, Rear Case: 1 단계, 이미지 1/1

    • Using the PH#00 screwdriver, remove the two 0.145 inch Phillips head screws.

    • The screws are located on the bottom face of the device, near the power and volume controls.

    편집

  2. Hipstreet Titan 2 HD Speaker Replacement: 2 단계, 이미지 1/1

    • Place the small suction cup on your screen.

    • Moisturize the bottom of the suction cup to ensure a proper seal.

    • If the screen is cracked, the suction cup may not seal correctly; too much pressure may crack or damage the screen.

    편집

  3. Hipstreet Titan 2 HD Speaker Replacement: 3 단계, 이미지 1/1

    • Insert the plastic opening tool between the screen cover and rear cover of the tablet.

    • Grasp the small suction cup.

    편집

  4. Hipstreet Titan 2 HD Speaker Replacement: 4 단계, 이미지 1/2 Hipstreet Titan 2 HD Speaker Replacement: 4 단계, 이미지 2/2

    • Slide the plastic opening tool along device edge to separate the screen cover from the rear cover.

    • Pull upward on the small suction cup handle while sliding the opening tool.

    • When sliding the plastic opening tool, avoid sliding the tool too far into the cover. This could damage the speaker connector on the back cover.

    편집

  6. Hipstreet Titan 2 HD Speaker Replacement: 5 단계, 이미지 1/2 Hipstreet Titan 2 HD Speaker Replacement: 5 단계, 이미지 2/2

    • Use the plastic opening tool to remove the speaker from the rear cover.

    • The speaker is held in place with adhesive and is easily removed.

    • Do not pull on the speaker wires. This could damage the soldering connections.

    편집

  7. Hipstreet Titan 2 HD Speaker Replacement: 6 단계, 이미지 1/1

    • Once the speaker is disconnected, the cover removal is complete.

    편집

  8. Hipstreet Titan 2 HD Speaker Replacement, Speaker: 7 단계, 이미지 1/1

    • Remove the black placement tape.

    편집

  9. Hipstreet Titan 2 HD Speaker Replacement: 8 단계, 이미지 1/1

    • Using a #PH000 screwdriver, remove the three 0.145in circuit board placement screws.

    편집

  10. Hipstreet Titan 2 HD Speaker Replacement: 9 단계, 이미지 1/3 Hipstreet Titan 2 HD Speaker Replacement: 9 단계, 이미지 2/3 Hipstreet Titan 2 HD Speaker Replacement: 9 단계, 이미지 3/3

    • Lift the hinge locks on the three ribbon connectors and disconnect the ribbon connectors.

    편집

  11. Hipstreet Titan 2 HD Speaker Replacement: 10 단계, 이미지 1/1

    • Identify the two soldered connectors for the speaker.

    편집

  12. Hipstreet Titan 2 HD Speaker Replacement: 11 단계, 이미지 1/1

    • Using a solder removal tool, remove the speaker soldered connectors.

    • Solder the new speaker wire connections to circuit board.

    • First solder the red wire on the left, then the black wire on the right.

    • Solder can burn you. Use caution.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 7명과 함께

Jeffrey

회원 가입일: 03/11/15

766 평판

안내서 5개 작성하였습니다

배지: 10

배지 +7개 더

팀

Colorado Springs, Team 5-6, Panko Spring 2015 Colorado Springs, Team 5-6, Panko Spring 2015 회원

UCCS-PANKO-S15S5G6

3 회원들

안내서 10개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 304