소개

If the wheel of your hoverboard is damaged or your hoverboard does not spin on one side, use this guide to replace the wheel and motor in the Hover-1 Titan.

  1. Flip the hoverboard so the bottom is facing up.
    • Flip the hoverboard so the bottom is facing up.

    • The left side is the side that has the charge port. There is also an "L" on the metal plate underneath the wires.

    댓글 쓰기

  2. Using a Phillips #1 screwdriver, remove the two 14 mm screws located closest to the center of the hoverboard.
    • Using a Phillips #1 screwdriver, remove the two 14 mm screws located closest to the center of the hoverboard.

    • Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.

    • Using a Phillips #1 screwdriver, remove two 15 mm screws located closest to the wheel.

    댓글 쓰기

    • Grip the bottom left panel and lift up to remove.

    댓글 쓰기

    • Unplug the battery by pulling apart the yellow connectors.

    댓글 쓰기

    • Use the Phillips #1 screwdriver to remove the four 12mm screws that attach the gyroscope/motherboard to the hoverboard.

    댓글 쓰기

    • Cut the rubber surrounding the yellow wire and pull the rubber apart, exposing the connectors.

    댓글 쓰기

  3. Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    • Unplug the yellow wires by gripping the wire close to the connectors and pulling apart.

    댓글 쓰기

    • Cut the rubber surrounding the green wire and pull the rubber apart, exposing the connectors.

    댓글 쓰기

    • Unplug the green wires by gripping the wire close to the connectors and pulling apart.

    댓글 쓰기

    • Cut the rubber surrounding the blue wire and pull the rubber apart, exposing the connectors.

    댓글 쓰기

    • Unplug the blue wires by gripping the wire close to the connectors and pulling apart.

    댓글 쓰기

    • Unplug the rainbow connector by squeezing the clips and pulling apart.

    댓글 쓰기

    • Use scissors to cut the zip tie around the group of wires.

    댓글 쓰기

    • Unplug the white wire connector by squeezing the clips and pulling apart.

    댓글 쓰기

    • Use an impact driver with a hex 6 bit to loosen the four 20 mm hex 6 bolts.

    • Wear safety glasses while using the impact driver.

    댓글 쓰기

    • Pull out the loosened screws with your hands and remove the metal plate.

    댓글 쓰기

    • Lift the wheel and motor shaft up and out of the board.

    • The motor shaft is located within the wheel.

    댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

Emma Huun

회원 가입일: 2018년 10월 08일

279 평판

안내서 1개 작성함

Cal Poly, Team S15-G4, White Fall 2018 Cal Poly, Team S15-G4, White Fall 2018 회원

CPSU-WHITE-F18S15G4

4 회원들

안내서 8개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 8

전체 시간: 32