메뉴

설정

India Mark III Chain Replacement

작성자 Andrew Optimus Goldheart (또 다른 기여자 5명)
  • 댓글 0
  • 즐겨찾기 0

난이도

보통

단계

8

소요 시간

시간 제안??

섹션

1

플래그

1

Prerequisite Only

단지 전제 조건

해당 안내서는 단지 다른 안내서의 전제 조건임을 참고하시기 바랍니다.

소개

Prereq only.

도구

부품

지정된 부품이 없습니다.

  1. Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up. Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up. Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up.

    • Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up.

    편집

  2. The following procedure requires two people. If you attempt to do this alone, you risk injuring yourself and damaging the pump. Lift the pump handle until the base of the chain comes to rest on the spacer collar, and the chain is slack. Hold the handle in this position while the chain is being detached. Lift the pump handle until the base of the chain comes to rest on the spacer collar, and the chain is slack. Hold the handle in this position while the chain is being detached.

    • The following procedure requires two people. If you attempt to do this alone, you risk injuring yourself and damaging the pump.

    • Lift the pump handle until the base of the chain comes to rest on the spacer collar, and the chain is slack. Hold the handle in this position while the chain is being detached.

    편집

  3. Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle. Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle. Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle.

    • Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle.

    편집

  5. Hold the wrench on the bolt stationary. Loosen the nut. Loosen the nut.

    • Hold the wrench on the bolt stationary.

    • Loosen the nut.

    편집

  6. Remove the nut from the chain bolt. Remove the nut from the chain bolt. Remove the nut from the chain bolt.

    • Remove the nut from the chain bolt.

    편집

  7. Remove the washer from the chain bolt. Remove the washer from the chain bolt.

    • Remove the washer from the chain bolt.

    편집

  8. Remove the chain bolt. Remove the chain bolt.

    • Remove the chain bolt.

    편집

  9. Pull the top of the chain straight off of the pump handle. Pull the top of the chain straight off of the pump handle. Pull the top of the chain straight off of the pump handle.

    • Pull the top of the chain straight off of the pump handle.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 5명과 함께

Andrew Optimus Goldheart

회원 가입일: 2009년 10월 17일

429,814 평판

안내서 411개 작성하였습니다

배지: 43

배지 +40개 더

팀

iFixit iFixit 회원

Community

107 회원들

안내서 9,569개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 25