물건을 수리하세요 커뮤니티 상점
수리 커뮤니티 가입 - 계정 만들기

Infinity Genesis hood Replacement

필요한 것

  1. Infinity Genesis hood Replacement, Hood: 1 단계, 이미지 3개 중 1개 Infinity Genesis hood Replacement, Hood: 1 단계, 이미지 3개 중 2개 Infinity Genesis hood Replacement, Hood: 1 단계, 이미지 3개 중 3개

    • To begin remove Right and Left armrests . See assembly guide on how to remove these.

    • Unzip the following zipper at the very top of the chair. It is hidden beneath Velcro .

    • Leave back pad like this no need to unzip any other zippers.

    편집

  2. Infinity Genesis hood Replacement: 2 단계, 이미지 3개 중 1개 Infinity Genesis hood Replacement: 2 단계, 이미지 3개 중 2개 Infinity Genesis hood Replacement: 2 단계, 이미지 3개 중 3개

    • Remove all 8 Screws on back cover.

    • End Result should like this .

    편집

  3. Infinity Genesis hood Replacement: 3 단계, 이미지 2개 중 1개 Infinity Genesis hood Replacement: 3 단계, 이미지 2개 중 2개

    • Remove Top 4 screws .

    편집

  5. Infinity Genesis hood Replacement: 4 단계, 이미지 3개 중 1개 Infinity Genesis hood Replacement: 4 단계, 이미지 3개 중 2개 Infinity Genesis hood Replacement: 4 단계, 이미지 3개 중 3개

    • You will need to disconnect the power cables on Left and Ride side of the hood assembly . They are attached via a clip. Simply push the clip down and pull them apart.

    편집

  6. Infinity Genesis hood Replacement: 5 단계, 이미지 3개 중 1개 Infinity Genesis hood Replacement: 5 단계, 이미지 3개 중 2개 Infinity Genesis hood Replacement: 5 단계, 이미지 3개 중 3개

    • You need to find the 6 way air valve on the left and right hand side.

    • You then need to Locate and remove the top air hose from the valve. You can usually identify this hose by the armor cover it has on it . Additionally its the only air hose that goes to the top.

    편집

  7. Infinity Genesis hood Replacement: 6 단계, 이미지 2개 중 1개 Infinity Genesis hood Replacement: 6 단계, 이미지 2개 중 2개

    • BEFORE CONTINUING DOUBLE CHECK YOU HAVE DONE THE PREVIOUS STEPS TO ENSURE EVERYTHING HAS BEEN DISCONNECTED .

    • To remove the hood piece lift upwards to slide it off of the Frame points.

    • Marked here are the 4 frame points . Remember where these are for re- assembly.

    • See last photo for end result.

    편집

  8. Infinity Genesis hood Replacement, REASSEMBLY TIPS: 7 단계, 이미지 2개 중 1개 Infinity Genesis hood Replacement, REASSEMBLY TIPS: 7 단계, 이미지 2개 중 2개

    • For reassembly of back panel Please be sure to lock in these Ball and Joint pieces into each other . They are located at the top of the chair.

    • If you don't lock these in first you will have a harder time securing this panel back on . Additionally once these Ball and joint pieces are connected. Secure the middle screws on the cover first this will ensure the cover will line up with the other bolts.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

2다른 기여자 명과 함께

Nick

회원 가입일: 05/30/17

2,764 평판

안내서 16개를 작성함

배지: 5

배지 +2개 더

0가이드 댓글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 1

지난 30일: 11

전체 시간: 132