기기를 수리하세요 커뮤니티 상점

Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement

소개

The Insignia Flex 10.1 NS-P10W8100 motherboard is connected to several Zero Insertion Force (ZIF) connectors and ribbon cable connectors. Be sure you have unplugged every connector before attempting to free the motherboard.

필요한 것

  1. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement, Motherboard: 1 단계, 이미지 1/2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement, Motherboard: 1 단계, 이미지 2/2

    • Carefully open the laptop and remove the keyboard by disconnecting it.

    • Place keyboard to the side as you will not need it.

    • Beware of plastic clips on the side of the device.

    편집

  2. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 2 단계, 이미지 1/2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 2 단계, 이미지 2/2

    • Lay the screen flat on its surface and use the iFixit opening tool to remove the cover by gently prying the back cover from the screen.

    • Apply the opening tool to the edge closest to the screen.

    • Apply the opening tool to each side which will help pry the back cover evenly.

    • Do not pry on the bottom side of the device. This is the side across from the camera.

    편집

  3. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 3 단계, 이미지 1/1

    • Use your fingers and pry the back cover from the screen. You may need to wiggle the cover a bit to separate the pieces.

    • If the back cover does not come off, work your fingers around the corners and slowly pry the cover off using your fingers.

    • Be careful with potential sharp edges and any exposed electrical components.

    편집

  4. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 4 단계, 이미지 1/3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 4 단계, 이미지 2/3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 4 단계, 이미지 3/3

    • Gently remove the black tape from each of the three connectors.

    • It may help to move around the motherboard in a clockwise direction to remove each piece of tape.

    편집

  5. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 5 단계, 이미지 1/1

    • With a fingernail, gently remove the yellow tape from across the speaker wires.

    편집

  7. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 6 단계, 이미지 1/1

    • Once the pieces of tape are removed the resulting motherboard should look like this picture.

    • The ZIF connectors will be removed in a clockwise motion.

    • Secondly, the ribbon cable connectors will be unplugged to isolate the motherboard.

    편집

  8. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 7 단계, 이미지 1/2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 7 단계, 이미지 2/2

    • Unplug the smallest ZIF Connector by using you fingernail to flip up the small locking flap. Then safely pull the cable out.

    • Be careful not too pull too hard as the ZIF Connector is fragile and can be damaged easily.

    편집

  9. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 8 단계, 이미지 1/2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 8 단계, 이미지 2/2

    • Following a clockwise direction, continue unplugging the ZIF connectors by safely puling the cable out.

    편집

  10. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 9 단계, 이미지 1/1

    • Remove the ribbon cables by firstly disconnecting the cable located on the top right of the motherboard,

    • Be careful not to forcefully yank the cable as it could cause a wire to disconnect.

    편집

  11. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 10 단계, 이미지 1/1

    • Remove the remaining two bottom ribbon cables.

    편집

  12. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 11 단계, 이미지 1/3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 11 단계, 이미지 2/3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 11 단계, 이미지 3/3

    • Disconnect the three low profile connectors by using a spudger to prop up both sides. Then, lift the connectors straight up from their sockets.

    편집

  13. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 12 단계, 이미지 1/3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 12 단계, 이미지 2/3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 12 단계, 이미지 3/3

    • Using a Phillips #2 screwdriver, remove the three 4 mm screws to free the motherboard.

    편집

  14. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 13 단계, 이미지 1/2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 13 단계, 이미지 2/2

    • Pull the two pieces of grey tape off the motherboard.

    편집

  15. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 14 단계, 이미지 1/2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 14 단계, 이미지 2/2

    • Remove the motherboard by lifting it upward.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Edgar Rodriguez

회원 가입일: 02/12/19

971 평판

안내서 5개 작성하였습니다

배지: 6

배지 +3개 더

팀

Western Carolina University, Team S1-G2, Virtue Spring 2019 Western Carolina University, Team S1-G2, Virtue Spring 2019 회원

WCU-VIRTUE-S19S1G2

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 5

전체 시간: 594