기기를 수리하세요 커뮤니티 상점

Insignia NS-VCS14SL7 Power Button Replacement

소개

The Insignia 2-in-1 Handheld vacuum button may get jammed or the electrical components can stop working. In either case, this guide can show you how to fix or replace the power button.

필요한 것

  1. Insignia NS-VCS14SL7 Power Button Replacement, Battery: 1 단계, 이미지 1/2 Insignia NS-VCS14SL7 Power Button Replacement, Battery: 1 단계, 이미지 2/2

    • Push down the black button to release the dust cup.

    • Pull the dust cup up and away from handheld portion to remove.

    번역하기

  2. Insignia NS-VCS14SL7 Power Button Replacement: 2 단계, 이미지 1/3 Insignia NS-VCS14SL7 Power Button Replacement: 2 단계, 이미지 2/3 Insignia NS-VCS14SL7 Power Button Replacement: 2 단계, 이미지 3/3

    • Remove the five 12.0 mm screws on the back of the handheld portion using the Phillips #2 screwdriver.

    • Lift the silver cover off of the black body of the handheld portion to expose the battery and wiring.

    번역하기

  3. Insignia NS-VCS14SL7 Power Button Replacement: 3 단계, 이미지 1/2 Insignia NS-VCS14SL7 Power Button Replacement: 3 단계, 이미지 2/2

    • Pull apart the red and black wires.

    • Do so for all of the wires. (Red x1, Black x2)

    번역하기

  5. Insignia NS-VCS14SL7 Power Button Replacement: 4 단계, 이미지 1/1

    • Remove the tape holding the battery to the black housing.

    • Slide the entire battery bundle out.

    번역하기

  6. Insignia NS-VCS14SL7 Power Button Replacement, Handheld Vacuum Power Button: 5 단계, 이미지 1/1

    • Remove motor and impeller housing to gain access to power button.

    번역하기

  7. Insignia NS-VCS14SL7 Power Button Replacement: 6 단계, 이미지 1/2 Insignia NS-VCS14SL7 Power Button Replacement: 6 단계, 이미지 2/2

    • Pry upwards on the retaining clip with black plastic spudger and pull to remove the 5 pin connector.

    번역하기

  8. Insignia NS-VCS14SL7 Power Button Replacement: 7 단계, 이미지 1/2 Insignia NS-VCS14SL7 Power Button Replacement: 7 단계, 이미지 2/2

    • Remove the two 10mm Philips #2 screws holding the brown printed circuit board to the vacuum.

    • Remove brown printed circuit board.

    • Pull up on clear plastic power button assembly to remove.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Thibaut Pillot

회원 가입일: 02/15/18

434 평판

안내서 5개 작성하였습니다

배지: 3

팀

USF Tampa, Team S16-G3, Boczar Spring 2018 USF Tampa, Team S16-G3, Boczar Spring 2018 회원

USFT-BOCZAR-S18S16G3

4 회원들

안내서 12개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 6

전체 시간: 204