기기를 수리하세요 커뮤니티 상점

Iomega Z100S2 Motherboard Replacement

필요한 것

  1. Iomega Z100S2 Motherboard Replacement, Case: 1 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement, Case: 1 단계, 이미지 2/2

    • Push in the plastic tab that can be seen through cracks in the front left corner using a spudger.

    편집

  2. Iomega Z100S2 Motherboard Replacement: 2 단계, 이미지 1/1

    • Move down the same side and push in the plastic tab.

    편집

  3. Iomega Z100S2 Motherboard Replacement: 3 단계, 이미지 1/1

    • Move to the front right side and once again push in the plastic tab.

    • There is not a fourth tab to push in after this one.

    편집

  4. Iomega Z100S2 Motherboard Replacement: 4 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement: 4 단계, 이미지 2/2

    • Grab the cover by the front side and pull upwards.

    • You might encounter some resistance. Pull firmly, but don't yank it.

    편집

  5. Iomega Z100S2 Motherboard Replacement: 5 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement: 5 단계, 이미지 2/2

    • Tilt the front case down until the pegs detach from the bottom of the case.

    • Lift up and outward.

    • The motherboard will be loose at this point.

    편집

  7. Iomega Z100S2 Motherboard Replacement, Disk Reader: 6 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement, Disk Reader: 6 단계, 이미지 2/2

    • Unhook the two springs from the front plastic hooks.

    • The black side rails of the reader should easily slide forward and off.

    편집

  8. Iomega Z100S2 Motherboard Replacement: 7 단계, 이미지 1/1

    • There is a white tab connected to the motherboard. Pull it upward by gently rocking it back and forth.

    • The tab does not come completely out, it only slides up slightly, so don't rip it out!

    편집

  9. Iomega Z100S2 Motherboard Replacement: 8 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement: 8 단계, 이미지 2/2

    • Grab the reader by its sides and gently pull it upward.

    • There are two wires still connected to the bottom of the reader that haven't been detached.

    편집

  10. Iomega Z100S2 Motherboard Replacement: 9 단계, 이미지 1/1

    • Disconnect the white wires by using tweezers to gently pull the bottom connector toward you.

    편집

  11. Iomega Z100S2 Motherboard Replacement: 10 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement: 10 단계, 이미지 2/2

    • Disconnect the thin ribbon wire by using tweezers to gently pull the connector at the bottom toward you.

    편집

  12. Iomega Z100S2 Motherboard Replacement: 11 단계, 이미지 1/1

    • Lift the reader up and out from the device.

    편집

  13. Iomega Z100S2 Motherboard Replacement, Motherboard: 12 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement, Motherboard: 12 단계, 이미지 2/2

    • Use a T6 Torx Screwdriver to remove the 1.3 mm screw at the back of the motherboard.

    편집

  14. Iomega Z100S2 Motherboard Replacement: 13 단계, 이미지 1/2 Iomega Z100S2 Motherboard Replacement: 13 단계, 이미지 2/2

    • Gently lift the motherboard and back case out from the bottom case.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Ezery Kennedy

회원 가입일: 10/05/10

288 평판

안내서 2개 작성하였습니다

배지: 11

배지 +8개 더

팀

Cal Poly, Team 7-53, Amido Fall 2010 Cal Poly, Team 7-53, Amido Fall 2010 회원

CPSU-AMIDO-F10S7G53

4 회원들

안내서 6개 작성하였습니다

댓글 한 개

how to fix the motherboard if booth leds stay lit when powering up?

ACIDGREEN TECHNO - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 8

전체 시간: 3,426