기기를 수리하세요 커뮤니티 상점

JBL On Stage II 30-Pin Connector Replacement

소개

This guide provides the steps necessary in order to replace the thirty-pin connector.

필요한 것

  1. JBL On Stage II 30-Pin Connector Replacement, Cracking the Case: 1 단계, 이미지 1/1

    • Turn the device upside down so that the three rubber pads are facing up.

    편집

  2. JBL On Stage II 30-Pin Connector Replacement: 2 단계, 이미지 1/1

    • Use a heat gun (set to low) to apply heat to one of the rubber pads until you can easily remove the pad. This step takes around 5-7 minutes.

    편집

  3. JBL On Stage II 30-Pin Connector Replacement: 3 단계, 이미지 1/1

    • Remove the heated rubber pad with a plastic opening tool.

    • Repeat steps 2 and 3 for the two remaining rubber pads.

    편집

  4. JBL On Stage II 30-Pin Connector Replacement: 4 단계, 이미지 1/2 JBL On Stage II 30-Pin Connector Replacement: 4 단계, 이미지 2/2

    • Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver.

    편집

  6. JBL On Stage II 30-Pin Connector Replacement: 5 단계, 이미지 1/3 JBL On Stage II 30-Pin Connector Replacement: 5 단계, 이미지 2/3 JBL On Stage II 30-Pin Connector Replacement: 5 단계, 이미지 3/3

    • Open the device along its seam.

    • Be careful when separating the device because there are wires connecting the two seperate halves.

    편집

  7. JBL On Stage II 30-Pin Connector Replacement: 6 단계, 이미지 1/1

    • Disconnect the ribbon cable connector from the top half of the device by pulling outward and parallel to the connecting pins.

    편집

  8. JBL On Stage II 30-Pin Connector Replacement: 7 단계, 이미지 1/2 JBL On Stage II 30-Pin Connector Replacement: 7 단계, 이미지 2/2

    • Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device.

    편집

    Where do I find these speakers

    HighChief - 답글

  9. JBL On Stage II 30-Pin Connector Replacement, 30-Pin Connector Replacement: 8 단계, 이미지 1/1

    • Apply heat with a heatgun on a low setting to the area around the 30-pin connector until you can easily pry it out by the seam surrounding it (about 10 minutes).

    편집

  10. JBL On Stage II 30-Pin Connector Replacement: 9 단계, 이미지 1/1

    • Use a metal spudger to pry out the plastic surrounding the 30-pin connector.

    편집

  11. JBL On Stage II 30-Pin Connector Replacement: 10 단계, 이미지 1/1

    • Use a pair of tweezers to wiggle out the 30-pin connector.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Janessa D Cabrera

회원 가입일: 01/23/14

514 평판

안내서 4개 작성하였습니다

배지: 10

배지 +7개 더

팀

Cal Poly, Team 9-28, Maness Winter 2014 Cal Poly, Team 9-28, Maness Winter 2014 회원

CPSU-MANESS-W14S9G28

4 회원들

안내서 7개 작성하였습니다

댓글 2개

and how you get a new one of the 30 pin connector?

bini barazany - 답글

Yes, where can we buy a new one of the 30 pin connector?

Jimbo - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 9

전체 시간: 4,426