주요 콘텐츠로 건너뛰기

Jumper Angelsounds JPD-100S Headphone Jacks Replacement

필요한 것

  1. Jumper Angelsounds JPD-100S Headphone Jacks Replacement, Motherboard: 1 단계, 이미지 1/1
    • Access the battery compartment

    • Remove the battery compartment lid and set it aside.

    • Disconnect the battery and set it aside.

  2. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 2 단계, 이미지 1/2 Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 2 단계, 이미지 2/2
    • Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

  3. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 3 단계, 이미지 1/1
    • Remove the 7mm Phillips #1 screw from the battery compartment.

    • Place the screw in a secure place.

  4. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 4 단계, 이미지 1/2 Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 4 단계, 이미지 2/2
    • Begin prying open the device.

    • Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.

    • Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

  5. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 5 단계, 이미지 1/2 Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 5 단계, 이미지 2/2
    • Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.

    • Create separation on that side until the white plastic component comes off entirely.

    • Place the white plastic component in a secure place.

  6. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 6 단계, 이미지 1/1
    • With your hand, remove the pink component.

  7. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 7 단계, 이미지 1/1
    • Remove the 7mm Phillips #1 screw in the middle of the motherboard.

  8. Jumper Angelsounds JPD-100S Headphone Jacks Replacement, Headphone Jacks: 8 단계, 이미지 1/1
    • Take the battery connector out of the battery compartment.

  9. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 9 단계, 이미지 1/1
    • Preheat the soldering iron .

    • Locate the wires that connect to the transducer.

    • Use a soldering iron and solder vacuum to unsolder the wires connected to the transducer.

  10. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 10 단계, 이미지 1/2 Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 10 단계, 이미지 2/2
    • Place the motherboard in a position that allows easy access to the jacks.

  11. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 11 단계, 이미지 1/3 Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 11 단계, 이미지 2/3 Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 11 단계, 이미지 3/3
    • Desolder the three solder joints securing each of the headphone jacks.

    • Try not to melt the motherboard when removing solder that secures the jacks.

  12. Jumper Angelsounds JPD-100S Headphone Jacks Replacement: 12 단계, 이미지 1/1
    • Remove the jacks by pulling them out of the motherboard.

결론

To reassemble your device, follow these instructions in reverse order.

Yessika Lugo

회원 가입일: 08/31/15

113 평판

안내서 1개 작성함

USF Tampa, Team 6-1, Remmell Fall 2015 USF Tampa, Team 6-1, Remmell Fall 2015 회원

USFT-REMMELL-F15S6G1

6 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 2

전체 시간: 358