기기를 수리하세요 커뮤니티 상점

Kawasaki KX 250F Handlebars Replacement

소개

This guide can be used for any type of dirt bike. This guide will show you the steps on removing broken handle bars and grips and replacing with new handle bars and grips.

필요한 것

  1. Kawasaki KX 250F Handlebars Replacement, Handlebars: 1 단계, 이미지 1/2 Kawasaki KX 250F Handlebars Replacement, Handlebars: 1 단계, 이미지 2/2

    • Use an 8mm socket to take off the front brake lever bolts and clutch lever bolts.

    번역하기

  2. Kawasaki KX 250F Handlebars Replacement: 2 단계, 이미지 1/1

    • Use a screwdriver to remove the kill switch bracket from the handlebars.

    번역하기

  3. Kawasaki KX 250F Handlebars Replacement: 3 단계, 이미지 1/1

    • Use pliers to clip off the metal bands around the grips.

    • There are 2 metal bands on each grip.

    번역하기

  4. Kawasaki KX 250F Handlebars Replacement: 4 단계, 이미지 1/1

    • Use a utility knife to cut off the old grips from the handlebars.

    번역하기

  5. Kawasaki KX 250F Handlebars Replacement: 5 단계, 이미지 1/1

    • Remove the old grips by peeling them down the bar.

    번역하기

  6. Kawasaki KX 250F Handlebars Replacement: 6 단계, 이미지 1/1

    • Use a screwdriver to loosen the screws on the throttle tube housing.

    • Do not fully remove the screws.

    번역하기

  7. Kawasaki KX 250F Handlebars Replacement: 7 단계, 이미지 1/1

    • Use a 10mm socket to remove all four bolts from the handlebar clamps.

    번역하기

  9. Kawasaki KX 250F Handlebars Replacement: 8 단계, 이미지 1/2 Kawasaki KX 250F Handlebars Replacement: 8 단계, 이미지 2/2

    • Remove the throttle tube from the handlebars.

    번역하기

  10. Kawasaki KX 250F Handlebars Replacement: 9 단계, 이미지 1/1

    • Slide the throttle tube onto the new handlebar.

    번역하기

  11. Kawasaki KX 250F Handlebars Replacement: 10 단계, 이미지 1/1

    • Place the handlebars in the clamps and tighten down the four bolts by hand.

    번역하기

  12. Kawasaki KX 250F Handlebars Replacement: 11 단계, 이미지 1/1

    • Use a screwdriver to tighten the throttle tube housing onto the new handlebar.

    번역하기

  13. Kawasaki KX 250F Handlebars Replacement: 12 단계, 이미지 1/1

    • Put on the clutch lever and tighten with an 8mm socket.

    번역하기

  14. Kawasaki KX 250F Handlebars Replacement: 13 단계, 이미지 1/1

    • Use the screwdriver to put the kill switch back on the new handlebar.

    번역하기

  15. Kawasaki KX 250F Handlebars Replacement: 14 단계, 이미지 1/1

    • Use an 8mm socket to put on the front brake lever and tighten it down.

    번역하기

  16. Kawasaki KX 250F Handlebars Replacement: 15 단계, 이미지 1/1

    • Spray hairspray into the grip.

    • The grips are two different sizes—the left side of the bar will get the smaller holed grip and the right side of the bar will get the grip with the larger hole.

    번역하기

  17. Kawasaki KX 250F Handlebars Replacement: 16 단계, 이미지 1/1

    • Slide the grip onto the handlebar.

    번역하기

  18. Kawasaki KX 250F Handlebars Replacement: 17 단계, 이미지 1/1

    • Spray hairspray into the grip.

    • The grips are two different sizes—the left side of the bar will get the smaller holed grip and the right side of the bar will get the grip with the larger hole.

    번역하기

  19. Kawasaki KX 250F Handlebars Replacement: 18 단계, 이미지 1/1

    • Slide the grip onto the handlebar.

    번역하기

  20. Kawasaki KX 250F Handlebars Replacement: 19 단계, 이미지 1/1

    • Use a 10mm socket to tighten the bolts for the handlebar clamps.

    • Sit on the bike to adjust the handlebars where you would like before tightening the bolts.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 1명과 함께

Ashley Sanders

회원 가입일: 04/04/19

292 평판

안내서 1개 작성함

배지: 5

배지 +2개 더

팀

Eastern Washington University, Team S25-G2, Crane Spring 2019 Eastern Washington University, Team S25-G2, Crane Spring 2019 회원

EWU-CRANE-S19S25G2

2 회원들

안내서 1개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 5

전체 시간: 371