기기를 수리하세요 커뮤니티 상점

KitchenAid KHM512ER Eject Button Spring Replacement

소개

Beater Eject Button doesn't work? Follow this guide to replace it.

필요한 것

  1. KitchenAid KHM512ER Eject Button Spring Replacement, Eject Button Spring: 1 단계, 이미지 1/2 KitchenAid KHM512ER Eject Button Spring Replacement, Eject Button Spring: 1 단계, 이미지 2/2

    • Insert the back of a plastic opening tool into one of the beater holes.

    • Apply force to pull the circular plastic part off.

    • If necessary, use the other side of the plastic opening tool to pry the circular plastic part off.

    편집

  2. KitchenAid KHM512ER Eject Button Spring Replacement: 2 단계, 이미지 1/3 KitchenAid KHM512ER Eject Button Spring Replacement: 2 단계, 이미지 2/3 KitchenAid KHM512ER Eject Button Spring Replacement: 2 단계, 이미지 3/3

    • Use a plastic opening tool to remove the speed knob.

    • Use a plastic opening tool to remove the long plastic piece

    • Use a plastic opening tool to remove the speed switch.

    편집

  4. KitchenAid KHM512ER Eject Button Spring Replacement: 3 단계, 이미지 1/2 KitchenAid KHM512ER Eject Button Spring Replacement: 3 단계, 이미지 2/2

    • Use a Phillips 2 screwdriver to remove the two 20.0mm screws holding the bottom plastic piece on.

    • Your screwdriver may not be long or narrow enough to reach the screws in these holes. If that's the case, use another screwdriver.

    • Remove the bottom plastic piece using a plastic opening tool.

    편집

  5. KitchenAid KHM512ER Eject Button Spring Replacement: 4 단계, 이미지 1/3 KitchenAid KHM512ER Eject Button Spring Replacement: 4 단계, 이미지 2/3 KitchenAid KHM512ER Eject Button Spring Replacement: 4 단계, 이미지 3/3

    • Using a Phillips 2 screwdriver, remove the three 20.0mm screws holding the motor assembly in place.

    • Use your hands to remove the motor assembly.

    • Use your hands to hold the eject button from one side while using the other hand to remove the circuit board.

    편집

  6. KitchenAid KHM512ER Eject Button Spring Replacement: 5 단계, 이미지 1/2 KitchenAid KHM512ER Eject Button Spring Replacement: 5 단계, 이미지 2/2

    • Remove the eject button by pulling it from the inside of the mixer.

    • Hold the eject button firmly while pulling out the spring.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Yuriy Zaynulin

회원 가입일: 02/10/16

191 평판

안내서 1개 작성함

배지: 8

배지 +5개 더

팀

USF Tampa, Team 2-3, Sullivan Spring 2016 USF Tampa, Team 2-3, Sullivan Spring 2016 회원

USFT-SULLIVAN-S16S2G3

3 회원들

안내서 4개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 7

전체 시간: 1,568