소개

How to remove the circuit board from an LG CG180 cell phone.

Power down the cell phone by pressing and holding down the red "end call" button.
  • Power down the cell phone by pressing and holding down the red "end call" button.

댓글 쓰기

Turn the phone screen-down so you are looking at the back cover.
  • Turn the phone screen-down so you are looking at the back cover.

댓글 쓰기

Slide the back cover down using your finger to remove the cover from the phone. Slide the back cover down using your finger to remove the cover from the phone.
  • Slide the back cover down using your finger to remove the cover from the phone.

댓글 쓰기

Place your finger at the top of the battery in small gap.
  • Place your finger at the top of the battery in small gap.

댓글 쓰기

Press downward while pulling outward to remove the battery.
  • Press downward while pulling outward to remove the battery.

댓글 쓰기

Remove all four screws on the back of the phone using a Phillips #00 screwdriver.
  • Remove all four screws on the back of the phone using a Phillips #00 screwdriver.

댓글 쓰기

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Insert a plastic opening tool in the seam.
  • Insert a plastic opening tool in the seam.

댓글 쓰기

Run the tool along the seam to release all the tabs. Run the tool along the seam to release all the tabs.
  • Run the tool along the seam to release all the tabs.

댓글 쓰기

Pull the phone back cover off once all the tabs are released. Pull the phone back cover off once all the tabs are released.
  • Pull the phone back cover off once all the tabs are released.

댓글 쓰기

Push the contents of the phone away from the hardshell case by applying pressure to the keypad with both thumbs.
  • Push the contents of the phone away from the hardshell case by applying pressure to the keypad with both thumbs.

댓글 쓰기

The hardshell case is separated from the rest of the phone.
  • The hardshell case is separated from the rest of the phone.

댓글 쓰기

Separate keypad from circuit board by turning it upside down and allowing it to fall off. Separate keypad from circuit board by turning it upside down and allowing it to fall off.
  • Separate keypad from circuit board by turning it upside down and allowing it to fall off.

댓글 쓰기

Place the circuit board with the display facing downward.
  • Place the circuit board with the display facing downward.

댓글 쓰기

Use thumb to release both white clips at the top of the circuit board.
  • Use thumb to release both white clips at the top of the circuit board.

  • Be careful with the display because it is still attached by electrical tape.

댓글 쓰기

Once both clips are released, turn over the circuit board so that the display is facing upward. Carefully lift the display from the left side and open to the right.
  • Once both clips are released, turn over the circuit board so that the display is facing upward.

  • Carefully lift the display from the left side and open to the right.

댓글 쓰기

Carefully remove the electrical tape from the display.
  • Carefully remove the electrical tape from the display.

댓글 쓰기

The display is disconnected from the circuit board.
  • The display is disconnected from the circuit board.

댓글 쓰기

The circuit board is separated from the rest of the phone.
  • The circuit board is separated from the rest of the phone.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

Alex Jacobs

회원 가입일: 2010년 01월 21일

5 평판

안내서 8개 작성하였습니다

Cal Poly, Team 14-42, Regan Winter 2010 Cal Poly, Team 14-42, Regan Winter 2010 회원

CPSU-REGAN-W10S14G42

4 회원들

안내서 10개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 2,730