기기를 고치세요

수리할 권리

부품 & 도구

LG CU400 Bottom Half Assembly Replacement

작성자 Dan Hughes (또 다른 기여자 4명)
  • 댓글 0
  • 즐겨찾기 0

난이도

보통

단계

9

소요 시간

10 분

섹션

2

플래그

1

Prerequisite Only

단지 전제 조건

해당 안내서는 단지 다른 안내서의 전제 조건임을 참고하시기 바랍니다.

소개

This guide will help you disassemble the bottom half of the phone. By completing this you will gain access to the motherboard and charging port for replacement.

  1. Push the button labeled 'PUSH' on the rear cover. Push the button labeled 'PUSH' on the rear cover.

    • Push the button labeled 'PUSH' on the rear cover.

    편집

  2. Slide the rear cover towards you. Slide the rear cover towards you. Slide the rear cover towards you.

    • Slide the rear cover towards you.

    편집

  3. To remove the battery, grasp the top front edge of the battery and pull the battery away from the phone. When installing the new battery, have the metal contacts of the phone match up with the metal contacts of the battery.

    • To remove the battery, grasp the top front edge of the battery and pull the battery away from the phone.

    • When installing the new battery, have the metal contacts of the phone match up with the metal contacts of the battery.

    편집

  4. Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits

    Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits

  5. Remove the sim card by sliding the card out from under the retainer using either your fingers or a spudger. Remove the sim card by sliding the card out from under the retainer using either your fingers or a spudger.

    • Remove the sim card by sliding the card out from under the retainer using either your fingers or a spudger.

    편집

  6. Remove the rubber covers in the highlighted locations using a metal spudger. Remove the rubber covers in the highlighted locations using a metal spudger.

    • Remove the rubber covers in the highlighted locations using a metal spudger.

    편집

  7. Remove the six 3mm #000 flat Phillips head screws from the back of the phone using a Phillips #000 Screwdriver. Remove the six 3mm #000 flat Phillips head screws from the back of the phone using a Phillips #000 Screwdriver.

    • Remove the six 3mm #000 flat Phillips head screws from the back of the phone using a Phillips #000 Screwdriver.

    편집

  8. Remove the headphone jack cover with your finger or metal spudger. Remove the headphone jack cover with your finger or metal spudger.

    • Remove the headphone jack cover with your finger or metal spudger.

    편집

  9. Insert the metal spudger between the keypad assembly and back cover assembly and pry the two assemblies apart. Pry gently as to not break the plastic clips that hold the two assemblies together. Work your way around the perimeter of the phone with the metal spudger to separate the two assemblies.

    • Insert the metal spudger between the keypad assembly and back cover assembly and pry the two assemblies apart.

    • Pry gently as to not break the plastic clips that hold the two assemblies together.

    • Work your way around the perimeter of the phone with the metal spudger to separate the two assemblies.

    편집

  10. Once you have worked your way around the perimeter of the phone, you will have access to the components in the bottom half assembly. Once you have worked your way around the perimeter of the phone, you will have access to the components in the bottom half assembly.

    • Once you have worked your way around the perimeter of the phone, you will have access to the components in the bottom half assembly.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 4명과 함께

Dan Hughes

회원 가입일: 2016년 10월 03일

1 평판

안내서 1개 작성함

배지: 4

+1개 배지 추가

팀

IUPUI, Team 1-3, Harley Fall 2016 IUPUI, Team 1-3, Harley Fall 2016 회원

IUPUI-HARLEY-F16S1G3

4 회원들

안내서 14개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 64